DTC C0200/31 Right Front Wheel Speed Sensor Signal |
DTC C0205/32 Left Front Wheel Speed Sensor Signal |
DTC C1271/71 Low Output Signal of Front Speed Sensor RH (Test Mode DTC) |
DTC C1272/72 Low Output Signal of Front Speed Sensor LH (Test Mode DTC) |
DTC C1275/75 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) |
DTC C1276/76 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) |
DTC C1330/35 Open Circuit in Right Front Wheel Speed Sensor Circuit |
DTC C1331/36 Open Circuit in Left Front Wheel Speed Sensor Circuit |

| DTC Code | DTC Detection Condition | Trouble Area |
| C0200/31 C0205/32 | When any of following conditions detected:
|
|
| C1271/71 C1272/72 | Detected only during test mode. |
|
| C1275/75 C1276/76 | Detected only during test mode. |
|
| C1330/35 C1331/36 | Open in front speed sensor circuit continues for 0.15 seconds or more. |
|

| 1.READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Select the Data List mode on the Techstream.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Wheel Speed | Front wheel speed sensor RH reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph) | Actual wheel speed | Similar speed as indicated on speedometer |
| FL Wheel Speed | Front wheel speed sensor LH reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph) | Actual wheel speed | Similar speed as indicated on speedometer |
Check that the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer are almost the same when driving the vehicle.
|
| ||||
| OK | |
| 2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK) |
Perform a TEST MODE inspection and check for DTCs (Click here).
|
| ||||
| OK | |
| 3.RECONFIRM DTC |
Clear the DTC(s) (Click here).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC(s) is output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | ||
| ||
| 4.CHECK FRONT SPEED SENSOR INSTALLATION |
![]() |
Check that the speed sensor installation bolt is tightened properly.
|
| ||||
| OK | |
| 5.CHECK FRONT SPEED SENSOR |
Visually check the speed sensor for deformation and damage.
|
| ||||
| OK | |
| 6.CHECK SPEED SENSOR TIP |
Remove the speed sensor (Click here).
Check the sensor tip.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR) |
![]() |
Confirm that the skid control ECU connector and speed sensor connector are properly connected.
Disconnect the A19 ECU connector.
Disconnect the z3 and z4 sensor connectors.
Inspect both the connector case and the terminal for deformation and corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A19-45 (FR+) - z3-2 (FR+) | Always | Below 1 Ω |
| A19-46 (FR-) - z3-1 (FR-) | ||
| A19-45 (FR+) - Body ground | Always | 10 kΩ or higher |
| A19-46 (FR-) - Body ground |
| Tester Connection | Condition | Specified Condition |
| A19-34 (FL+) - z4-2 (FL+) | Always | Below 1 Ω |
| A19-33 (FL-) - z4-1 (FL-) | ||
| A19-34 (FL+) - Body ground | Always | 10 kΩ or higher |
| A19-33 (FL-) - Body ground |
|
| ||||
| OK | |
| 8.INSPECT FRONT SPEED SENSOR (INPUT VOLTAGE) |
![]() |
Reconnect the A19 ECU connector.
Disconnect the z3 and z4 sensor connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z3-2 (FR+) - Body ground | Ignition switch ON | 7.5 to 20 V |
| z4-2 (FL+) - Body ground |
|
| ||||
| OK | |
| 9.RECONFIRM DTC |
Clear the DTC(s) (Click here).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC(s) is output (Click here).
| Result | Proceed to |
| DTC is output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 10.REPLACE FRONT SPEED SENSOR |
Replace the front speed sensor (Click here).
| NEXT | |
| 11.RECONFIRM DTC |
Clear the DTC(s) (Click here).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC(s) is output (Click here).
| Result | Proceed to |
| DTC is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||