Home › Engine / Hybrid System · 3UR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0351    Ignition Coil "A" Primary / Secondary Circuit

DTC    P0352    Ignition Coil "B" Primary / Secondary Circuit

DTC    P0353    Ignition Coil "C" Primary / Secondary Circuit

DTC    P0354    Ignition Coil "D" Primary / Secondary Circuit

DTC    P0355    Ignition Coil "E" Primary / Secondary Circuit

DTC    P0356    Ignition Coil "F" Primary / Secondary Circuit

DTC    P0357    Ignition Coil "G" Primary / Secondary Circuit

DTC    P0358    Ignition Coil "H" Primary / Secondary Circuit

for Preparation Click here


DESCRIPTION

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is stored, check the No. 1 ignition coil with igniter circuit.
  3. If DTC P0352 is stored, check the No. 2 ignition coil with igniter circuit.
  4. If DTC P0353 is stored, check the No. 3 ignition coil with igniter circuit.
  5. If DTC P0354 is stored, check the No. 4 ignition coil with igniter circuit.
  6. If DTC P0355 is stored, check the No. 5 ignition coil with igniter circuit.
  7. If DTC P0356 is stored, check the No. 6 ignition coil with igniter circuit.
  8. If DTC P0357 is stored, check the No. 7 ignition coil with igniter circuit.
  9. If DTC P0358 is stored, check the No. 8 ignition coil with igniter circuit.

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A147863E06


DTC No.
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
P0355
P0356
P0357
P0358
No IGF signal to ECM while engine running
(1 trip detection logic)
  1. Ignition system
  2. Open or short in IGF1 or IGT circuit (1 to 8) between ignition coil with igniter and ECM
  3. No. 1 to No. 8 ignition coils with igniters
  4. ECM
  1. Reference: Inspection using an oscilloscope.

  2. A093278E24

    Standard:

    Tester Connection
    Tool Setting
    Condition
    Specified Condition
    D56-40 (IGT1) - D56-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    The correct waveform is as shown
    D56-33 (IGT2) - D56-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    The correct waveform is as shown
    D56-37 (IGT3) - D56-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    The correct waveform is as shown
    D56-34 (IGT4) - D56-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    The correct waveform is as shown
    D56-35 (IGT5) - D56-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    The correct waveform is as shown
    D56-36 (IGT6) - D56-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    The correct waveform is as shown
    D56-38 (IGT7) - D56-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    The correct waveform is as shown
    D56-39 (IGT8) - D56-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    The correct waveform is as shown
    D56-104 (IGF1) - D56-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    The correct waveform is as shown
    D56-105 (IGF2) - D56-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    The correct waveform is as shown

    HINT:
    While cranking or idling the engine, check the waveform between terminals IGT (1 to 8) and E1, and IGF1 or IGF2 and E1 of the ECM connector.


MONITOR DESCRIPTION


A115898E06

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored 1 second after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0351: Igniter (cylinder 1) malfunction
P0352: Igniter (cylinder 2) malfunction
P0353: Igniter (cylinder 3) malfunction
P0354: Igniter (cylinder 4) malfunction
P0355: Igniter (cylinder 5) malfunction
P0356: Igniter (cylinder 6) malfunction
P0357: Igniter (cylinder 7) malfunction
P0358: Igniter (cylinder 8) malfunction
Required Sensors/Components (Main)
Igniter
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
About 1 second
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Either of following conditions A or B met
-
A. Engine RPM
1500 rpm or less
B. Starter
OFF
Either of following conditions C or D met
-
C. Both of following conditions (a) and (b) met
-
(a) Engine speed
500 rpm or less
(b) Battery voltage
6 V or more
D. All of following conditions (a), (b) and (c) met
-
(a) Engine speed
More than 500 rpm
(b) Battery voltage
10 V or more
(c) Number of sparks after CPU reset
5 sparks or more

TYPICAL MALFUNCTION THRESHOLDS


IGF signal
ECM does not receive any IGF signal despite ECM sending IGT signal to igniter

COMPONENT OPERATING RANGE


IGF signal
Igniter transmits IGF signal when it receives IGT signal from ECM

WIRING DIAGRAM


A178647E02


A178648E02


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
A157860E30
  1. Disconnect the ignition coil with igniter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D5-4 (GND) - Body ground
    Always
    Below 1 Ω
    D13-4 (GND) - Body ground
    Always
    Below 1 Ω
    D6-4 (GND) - Body ground
    Always
    Below 1 Ω
    D12-4 (GND) - Body ground
    Always
    Below 1 Ω
    D7-4 (GND) - Body ground
    Always
    Below 1 Ω
    D11-4 (GND) - Body ground
    Always
    Below 1 Ω
    D8-4 (GND) - Body ground
    Always
    Below 1 Ω
    D10-4 (GND) - Body ground
    Always
    Below 1 Ω

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D5-1 (+B) - D5-4 (GND)
    Ignition switch ON
    11 to 14 V
    D13-1 (+B) - D13-4 (GND)
    Ignition switch ON
    11 to 14 V
    D6-1 (+B) - D6-4 (GND)
    Ignition switch ON
    11 to 14 V
    D12-1 (+B) - D12-4 (GND)
    Ignition switch ON
    11 to 14 V
    D7-1 (+B) - D7-4 (GND)
    Ignition switch ON
    11 to 14 V
    D11-1 (+B) - D11-4 (GND)
    Ignition switch ON
    11 to 14 V
    D8-1 (+B) - D8-4 (GND)
    Ignition switch ON
    11 to 14 V
    D10-1 (+B) - D10-4 (GND)
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
A164729E06
  1. Disconnect the ignition coil with igniter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D5-2 (IGF1) - D56-104 (IGF1)
    Always
    Below 1 Ω
    D13-2 (IGF2) - D56-105 (IGF2)
    Always
    Below 1 Ω
    D6-2 (IGF2) - D56-105 (IGF2)
    Always
    Below 1 Ω
    D12-2 (IGF1) - D56-104 (IGF1)
    Always
    Below 1 Ω
    D7-2 (IGF2) - D56-105 (IGF2)
    Always
    Below 1 Ω
    D11-2 (IGF1) - D56-104 (IGF1)
    Always
    Below 1 Ω
    D8-2 (IGF1) - D56-104 (IGF1)
    Always
    Below 1 Ω
    D10-2 (IGF2) - D56-105 (IGF2)
    Always
    Below 1 Ω
    D5-3 (IGT1) - D56-40 (IGT1)
    Always
    Below 1 Ω
    D13-3 (IGT2) - D56-33 (IGT2)
    Always
    Below 1 Ω
    D6-3 (IGT3) - D56-37 (IGT3)
    Always
    Below 1 Ω
    D12-3 (IGT4) - D56-34 (IGT4)
    Always
    Below 1 Ω
    D7-3 (IGT5) - D56-35 (IGT5)
    Always
    Below 1 Ω
    D11-3 (IGT6) - D56-36 (IGT6)
    Always
    Below 1 Ω
    D8-3 (IGT7) - D56-38 (IGT7)
    Always
    Below 1 Ω
    D10-3 (IGT8) - D56-39 (IGT8)
    Always
    Below 1 Ω
    D5-2 (IGF1) or D56-104 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D13-2 (IGF2) or D56-105 (IGF2) - Body ground
    Always
    10 kΩ or higher
    D6-2 (IGF2) or D56-105 (IGF2) - Body ground
    Always
    10 kΩ or higher
    D12-2 (IGF1) or D56-104 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D7-2 (IGF2) or D56-105 (IGF2) - Body ground
    Always
    10 kΩ or higher
    D11-2 (IGF1) or D56-104 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D8-2 (IGF1) or D56-104 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D10-2 (IGF2) or D56-105 (IGF2) - Body ground
    Always
    10 kΩ or higher
    D5-3 (IGT1) or D56-40 (IGT1) - Body ground
    Always
    10 kΩ or higher
    D13-3 (IGT2) or D56-33 (IGT2) - Body ground
    Always
    10 kΩ or higher
    D6-3 (IGT3) or D56-37 (IGT3) - Body ground
    Always
    10 kΩ or higher
    D12-3 (IGT4) or D56-34 (IGT4) - Body ground
    Always
    10 kΩ or higher
    D7-3 (IGT5) or D56-35 (IGT5) - Body ground
    Always
    10 kΩ or higher
    D11-3 (IGT6) or D56-36 (IGT6) - Body ground
    Always
    10 kΩ or higher
    D8-3 (IGT7) or D56-38 (IGT7) - Body ground
    Always
    10 kΩ or higher
    D10-3 (IGT8) or D56-39 (IGT8) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355, P0356, P0357 OR P0358)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Shuffle the arrangement of the ignition coils with igniters (among No. 1 to No. 8 cylinders).

    NOTICE:
    Do not shuffle the connectors.

  1. Perform a simulation test.

  1. Check DTCs displayed on the Techstream.
    Result 
    Result
    Proceed to
    Same DTC is output
    A
    Different ignition coil DTC is output
    B



B
REPLACE IGNITION COIL ASSEMBLY (Click here)
A

REPLACE ECM (Click here)