DTC P0365 Camshaft Position Sensor "B" Circuit (Bank 1) |
DTC P0367 Camshaft Position Sensor "B" Circuit Low Input (Bank 1) |
DTC P0368 Camshaft Position Sensor "B" Circuit High Input (Bank 1) |
DTC P0390 Camshaft Position Sensor "B" Circuit (Bank 2) |
DTC P0392 Camshaft Position Sensor "B" Circuit Low Input (Bank 2) |
DTC P0393 Camshaft Position Sensor "B" Circuit High Input (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0365 P0390 | No VVT sensor signal to ECM during engine running (1 trip detection logic) |
|
| P0367 P0392 | Output voltage of VVT sensor less than 0.3 V 4 seconds (1 trip detection logic) |
|
| P0368 P0393 | Output voltage of VVT sensor more than 4.7 V 4 seconds (1 trip detection logic) |
|
![]() |
| Tester Connection | Tool Setting | Condition | Specified Condition |
| D56-110 (NE+) - D56-111 (NE-) | 5 V/DIV. 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| D56-69 (EV1+) - D56-68 (EV1-) | 5 V/DIV. 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| D56-64 (EV2+) - D56-65 (EV2-) | 5 V/DIV. 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| Related DTCs | P0365: VVT sensor (for Bank 1) verify pulse input P0367: VVT position sensor (for Bank 1) range check (low voltage) P0368: VVT position sensor (for Bank 1) range check (high voltage) P0390: VVT sensor (for Bank 2) verify pulse input P0392: VVT position sensor (for Bank 2) range check (low voltage) P0393: VVT position sensor (for Bank 2) range check (high voltage) |
| Required Sensors/Components (Main) | VVT position sensor (for Bank 1 and 2) |
| Required Sensors/Components (Sub) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | 5 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs are not present | P0365, P0390 (Exhaust VVT Sensor) |
| Starter | OFF |
| Ignition switch | ON |
| Time after ignition switch off to ON | 2 seconds or more |
| Battery voltage | 8 V or more |
| Monitor runs whenever following DTCs are not present | P0367, P0368, P0392, P0393 (Exhaust VVT Sensor) |
| Exhaust VVT sensor voltage | 0.3 to 4.7 V |
| Engine speed | 600 rpm or more |
| Battery voltage | 8 V or more |
| Starter | OFF |
| Ignition switch | ON |
| Exhaust VVT sensor voltage | Less than 0.3 V |
| Exhaust VVT sensor voltage | More than 4.7 V |
| Exhaust VVT sensor signal | No signal |
| VVT sensor voltage | 0.3 to 4.7 V |

| 1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE) |
![]() |
Disconnect the VVT sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (VC2) - Body ground | Ignition switch ON | 4.5 to 5.0 V |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM) |
![]() |
Disconnect the VVT sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D24-1 (EX+) - D56-69 (EV1+) | Always | Below 1 Ω |
| D24-2 (EX-) - D56-68 (EV1-) | Always | Below 1 Ω |
| D25-1 (EX+) - D56-64 (EV2+) | Always | Below 1 Ω |
| D25-2 (EX-) - D56-65 (EV2-) | Always | Below 1 Ω |
| D24-1 (EX+) or D56-69 (EV1+) - Body ground | Always | 10 kΩ or higher |
| D24-2 (EX-) or D56-68 (EV1-) - Body ground | Always | 10 kΩ or higher |
| D25-1 (EX+) or D56-64 (EV2+) - Body ground | Always | 10 kΩ or higher |
| D25-2 (EX-) or D56-65 (EV2-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST CAMSHAFT) |
![]() |
Check the VVT sensor installation.
|
| ||||
| OK | |
| 4.INSPECT EXHAUST CAMSHAFT |
Check the teeth of the camshaft.
|
| ||||
| OK | |
| 5.REPLACE VVT SENSOR |
Replace the VVT sensor (Click here).
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read DTCs.
| Display (DTC Output) | Proceed to |
| No DTC is output | A |
| P0365, P0367, P0368, P0390, P0392 or P0393 are output | B |
|
| ||||
| A | ||
| ||