CAMSHAFT > REMOVAL |
| 1. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY |
Remove the timing chain cover (Click here).
| 2. SET NO. 1 CYLINDER TO TDC/COMPRESSION |
Temporarily install the pulley set bolt.
Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

| 3. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY (for LH Side) |
![]() |
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
![]() |
Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.
![]() |
Remove the 2 bolts, chain tensioner and gasket.
| 4. REMOVE CHAIN TENSIONER SLIPPER (for LH Side) |
![]() |
| 5. REMOVE NO. 1 CHAIN VIBRATION DAMPER (for LH Side) |
![]() |
Remove the 2 bolts and chain vibration damper.
| 6. REMOVE CHAIN SUB-ASSEMBLY (for LH Side) |
![]() |
While pushing down the No. 3 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.
![]() |
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
![]() |
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket LH.
Remove the No. 1 and No. 2 chains from the gears.
| 7. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY |
![]() |
Remove the 2 bolts and chain tensioner.
| 8. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY (for RH Side) |
![]() |
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
![]() |
Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.
![]() |
Remove the 2 bolts and chain tensioner.
| 9. REMOVE CHAIN TENSIONER SLIPPER (for RH Side) |
![]() |
| 10. REMOVE NO. 1 CHAIN VIBRATION DAMPER (for RH Side) |
![]() |
Remove the 2 bolts and vibration damper.
| 11. REMOVE CHAIN SUB-ASSEMBLY (for RH Side) |
![]() |
While raising up the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.
![]() |
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
![]() |
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket RH.
Remove the No. 1 and No. 2 chains from the gears.
| 12. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY |
![]() |
Remove the 2 bolts and chain tensioner.
| 13. REMOVE CAMSHAFT (for Bank 1) |
![]() |
Make sure that the knock pin of the camshaft is positioned as shown in the illustration.
![]() |
Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.
![]() |
Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.
Remove the 6 bearing caps.
Remove the No. 3 and No. 4 camshafts.
| 14. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH |
![]() |
Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.
| 15. REMOVE CAMSHAFT (for Bank 2) |
![]() |
Make sure that the knock pin of the camshaft is positioned as shown in the illustration.
![]() |
Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.
![]() |
Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.
Remove the 6 bearing caps.
Remove the No. 1 and No. 2 camshafts.
| 16. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH |
![]() |
Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.