Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1653/35    Seat Position Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The seat position airbag sensor circuit consists of the center airbag sensor and the seat position airbag sensor.
DTC B1653/35 is stored when a malfunction is detected in the seat position airbag sensor circuit.

DTC Code
Detection Condition
Trouble Area
B1653/35
When one of following conditions is met:
  1. The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position airbag sensor circuit for 2 seconds.
  2. Seat position airbag sensor malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Front seat inner belt assembly LH
  3. Seat position airbag sensor
  4. Center airbag sensor assembly

WIRING DIAGRAM


C162307E04


INSPECTION PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the seat position airbag sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and the seat position airbag sensor.

  1. Check that the connectors (on the center airbag sensor side and seat position airbag sensor side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


3.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (CENTER AIRBAG SENSOR - SEAT POSITION AIRBAG SENSOR)


  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


    C162324E03

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Ignition switch ON
    Below 1 V
    2 - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 13 (DSP-) and 14 (DSP+) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1 MΩ or higher
    1 - Body ground
    Always
    1 MΩ or higher
    2 - Body ground
    Always
    1 MΩ or higher



NG
Go to step 7
OK


4.CHECK SEAT POSITION AIRBAG SENSOR


    C162325E01
  1. Connect the connectors to the center airbag sensor and the seat position airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK (Click here)  

5.REPLACE SEAT POSITION AIRBAG SENSOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the seat position airbag sensor (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.


NEXT


6.CHECK CENTER AIRBAG SENSOR


    C162325E01
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END 

7.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)


  1. Disconnect the floor wire connector from the front seat inner belt LH.


    C172902E02

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O4-2 (LSP+) - Body ground
    Ignition switch ON
    Below 1 V
    O4-4 (LSP-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 13 (DSP-) and 14 (DSP+) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-2 (LSP+) - O4-4 (LSP-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-2 (LSP+) - O4-4 (LSP-)
    Always
    1 MΩ or higher
    O4-2 (LSP+) - Body ground
    Always
    1 MΩ or higher
    O4-4 (LSP-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)