Home › Engine / Hybrid System · CRUISE CONTROL › DYNAMIC LASER CRUISE CONTROL SYSTEM

DTC    U0235    Lost Communication with Cruise Control Front Distance Range Sensor

DTC    U1102    Lost Communication with Radar Sensor

for Preparation Click here


DESCRIPTION

The laser radar sensor and distance control ECU transmit the data for general vehicle control and diagnosis function along the communication line. The laser radar sensor transmits information about the vehicle in front to the distance control ECU.

DTC No.
DTC Detection Condition
Trouble Area
U0235
The ECM detects a communication error signal (from the laser radar sensor to the distance control ECU) for 0.15 seconds or more while the dynamic laser cruise control is in operation.
  1. Communication circuit
  2. Laser radar sensor
  3. Distance control ECU
U1102
The ECM detects a communication error signal (from the distance control ECU to the laser radar sensor) for 0.15 seconds or more while the dynamic laser cruise control is in operation
  1. Communication circuit
  2. laser radar sensor
  3. Distance control ECU

WIRING DIAGRAM


E163050E01


INSPECTION PROCEDURE

NOTICE:
  1. When the distance control ECU is replaced with a new one, initialization must be performed (Click here).
  2. When the laser radar sensor is replaced with a new one, adjustment of the laser radar sensor beam axis must be performed (Click here).

1.CHECK HARNESS AND CONNECTOR (DISTANCE CONTROL ECU - LASER RADAR SENSOR)


    E162388E04
  1. Disconnect the A43 distance control ECU connector and A26 laser radar sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A43-22 (LRDD) - A26-3 (LRDD)
    Always
    Below 1 Ω
    A43-13 (IGB) - A26-5 (IGB)
    Always
    Below 1 Ω
    A43-22 (LRDD) - Body ground
    Always
    10 kΩ or higher
    A43-13 (IGB) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the distance control ECU connector and laser radar sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT DISTANCE CONTROL ECU


    E135386E10
  1. Disconnect the A43 distance control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-13 (IGB) - Body ground
    Ignition switch ON
    11 to 14 V
    A43-22 (LRDD) - A43-10 (SGND)
    Ignition switch ON
    4.5 to 5.5 V

  1. Reconnect the distance control ECU connector.



NG
REPLACE DISTANCE CONTROL ECU (Click here)
OK


3.REPLACE LASER RADAR SENSOR
  1. Temporarily replace the laser radar sensor with a new or normally functioning one (Click here).


NEXT


4.ADJUST LASER RADAR SENSOR
  1. Adjust laser radar sensor (Click here).

HINT:
It is necessary to make the ECM recognize specification information (whether the vehicle is equipped with the dynamic laser cruise control system or not). When this procedure has not been carried out, this DTC may be output.


NEXT


5.CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


6.CHECK FOR DTC
  1. Reproduce the DTC detection conditions under which the DTC is stored.

    HINT:
    If the DTC detection conditions are not correct, the system will not detect the trouble.

  1. Drive the vehicle at a speed of 45 km/h (28 mph) or more and turn the cruise control main switch ON. Push the -SET switch to activate the cruise control system.

  1. Check for DTCs (Click here).

    OK:
    DTC is not output



NG
REPLACE DISTANCE CONTROL ECU (Click here)
OK

END (LASER RADAR SENSOR DEFECTIVE)