Home › Engine / Hybrid System · CRUISE CONTROL › CRUISE CONTROL SYSTEM

DTC    P0571    Brake Switch "A" Circuit

for Preparation Click here


DESCRIPTION

When the brake pedal is depressed, the stop light switch sends a signal to the ECM. When the ECM receives this signal, it cancels the cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the ECM through the STOP fuse and the stop light switch, and the ECM turns the cruise control off.

DTC No.
DTC Detection Condition
Trouble Area
P0571
Voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for 0.5 seconds. or more.
  1. Stop light switch
  2. Stop light switch circuit
  3. ECM

WIRING DIAGRAM


E162936E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Cruise Control / Data List.

  1. Check the Data List for proper functioning of the cruise control main switch.

    ECM (Laser Cruise) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW M-CPU
    Stop light switch signal (Main CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

    OK:
    Normal conditions listed above are displayed.

    Result 
    Result
    Proceed to
    NG
    A
    OK (for 2UZ-FE)
    B
    OK (for 3UR-FE)
    C
    OK (for 3UR-FBE)
    D



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)
A


2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - BATTERY)


    E144327E05
  1. Disconnect the A4 connector from the stop light switch.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A4-2 - Body ground
    Always
    11 to 14 V
    A4-3 - Body ground
    Ignition switch ON
    11 to 14 V

  1. Reconnect the connector from the stop light switch.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT STOP LIGHT SWITCH


    E146086E03
  1. Remove the stop light switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin not pushed
    Below 1 Ω
    3 - 4
    Switch pin not pushed
    10 kΩ or higher
    1 - 2
    Switch pin pushed
    10 kΩ or higher
    3 - 4
    Switch pin pushed
    Below 1 Ω

  1. Reinstall the stop light switch.



NG
REPLACE STOP LIGHT SWITCH (Click here)
OK


4.CHECK ECM


    E162181E02
  1. Disconnect the A27 connector from the ECM.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A27-26 (STP) - Body ground
    Brake pedal is depressed
    11 to 14 V
    A27-26 (STP) - Body ground
    Brake pedal is released
    Below 1 V
    A27-35 (ST1-) - Body ground
    Brake pedal is depressed
    Below 1 V
    A27-35 (ST1-) - Body ground
    Brake pedal is released
    11 to 14 V

    Result
    Proceed to
    NG
    A
    OK (for 2UZ-FE)
    B
    OK (for 3UR-FE)
    C
    OK (for 3UR-FBE)
    D

  1. Disconnect the ECM connector.



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH - ECM)