Home › Drivetrain · A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0818    Driveline Disconnect Switch Input Circuit

for Preparation Click here


DESCRIPTION

The ECM detects the signal indicating that the transfer is in neutral.
This DTC indicates that the signal indicating that the transfer is in neutral remains on.

DTC Code
DTC Detection Condition
Trouble Area
P0818
The signal indicating that the transfer is in neutral remains ON while vehicle is running under following conditions for 30 seconds (2 trip detection logic):
  1. Vehicle speed is 25 km/h (16 mph) or more
  2. Transfer position switch is in 4H
  1. Short in transfer neutral position switch circuit
  2. Transfer shift actuator assembly (transfer system)
  3. ECM

MONITOR DESCRIPTION

The ECM detects whether or not the transfer is in neutral by monitoring the signal from the transfer shift actuator assembly.
If the ECM detects that the transfer is in neutral under the following conditions, the ECM will conclude that there is a malfunction of the transfer shift actuator assembly, illuminate the MIL and store the DTC:
  1. The transfer shift actuator assembly indicates that the transfer is in neutral.
  2. The transfer position switch is in the 4H position.
  3. The vehicle is being driven at 25 km/h (16 mph) or more.
  4. The transfer neutral signal has been ON for more than 30 seconds.

MONITOR STRATEGY


Related DTCs
P0818: Transfer neutral position switch/Verify switch cycling
Required sensors/Components
Transfer neutral position switch, Vehicle speed sensor
Frequency of operation
Continuous
Duration
30 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
None
Vehicle speed
25 km/h (15.54 mph) or more
Transfer position
High
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


Transfer neutral switch signal
ON

WIRING DIAGRAM


C160106E12


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TRANSFER SHIFT ACTUATOR - BODY GROUND)


    C159074E11
  1. Disconnect the D46 transfer shift actuator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D46-3 (N) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
GO TO TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
A


2.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BODY GROUND)
C162221E13
  1. Disconnect the A28 4WD control ECU connector.

  1. Disconnect the D46 transfer shift actuator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A28-16 (NP) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
GO TO TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM (Click here)
A


3.CHECK HARNESS AND CONNECTOR (TRANSFER SHIFT ACTUATOR, 4WD CONTROL ECU - ECM)
C159423E44
  1. Disconnect the A27 ECM connector.

  1. Disconnect the D46 transfer shift actuator connector.

  1. Disconnect the A28 4WD control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A27-5 (TFN) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK
    A
    NG
    B



B
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ECM (Click here)