Home › Audio/Visual/Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM

DTC    01-DD    Master Reset

DTC    01-E1    Voice Processing Device ON Error

for Preparation Click here


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
01-DD*1
Device that should be master has been disconnected after engine starts.
  1. Navigation receiver assembly power source circuit
  1. AVC-LAN circuit between Navigation receiver assembly and component which has stored this code
  1. Navigation receiver assembly
  1. Component which has stored this code
01-E1*1, *2
Amplifier device records that amplifier output does not function even while source device is operating.

HINT:
  1. *1: This code may be stored if the engine started, idled for 60 seconds and then the ignition switch is turned to the start position again.
  2. *2: Even if no fault is present, this trouble code may be stored depending on the battery condition or engine start voltage.

NOTICE:
  1. Before starting troubleshooting, be sure to clear DTCs to clear codes stored due to the reasons described in Hint above. Then, check for DTCs and troubleshoot according to the output DTCs.
  2. The navigation receiver assembly is the master unit.
  3. Be sure to clear and recheck DTCs after the inspection is completed to confirm that no DTCs are output.


INSPECTION PROCEDURE

NOTICE:
Be sure to read Description before performing the following procedures.

1.CHECK NAVIGATION RECEIVER ASSEMBLY POWER SOURCE CIRCUIT
  1. Refer to the navigation receiver assembly power source circuit (Click here).
    If the power source circuit is operating normally, proceed to the next step.


NEXT


2.INSPECT NAVIGATION RECEIVER ASSEMBLY


    E145834E12
  1. Disconnect the I20 and I25* navigation receiver assembly connectors.

    HINT:
    *: w/ Rear Seat Entertainment System

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I20-5 (ATX+) - I20-15 (ATX-)
    Always
    60 to 80 Ω
    I25-9 (TXM+) - I25-10 (TXM-)*

    HINT:
    *: w/ Rear Seat Entertainment System

  1. Reconnect the navigation receiver assembly connectors.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


3.IDENTIFY COMPONENT WHICH HAS STORED THIS CODE


    E138069E01
  1. Enter the diagnostic mode.

  1. Press the "LAN Mon" switch to change to "LAN Monitor" mode.

  1. Identify the component which has stored this code.
    Component Table 
    Display
    Component
    AVN
    Navigation receiver assembly
    DSP-AMP
    Stereo component amplifier assembly
    Rr-TV*
    Television display assembly

    HINT:
    1. "DSP-AMP" is the component which has stored this code in the example shown in the illustration.
    2. *: w/ Rear Seat Entertainment System


NEXT


4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - COMPONENT WHICH HAS STORED THIS CODE)

HINT:
For details of the connectors, refer to "Terminals of ECU" (Click here).



  1. Referring to the AVC-LAN wiring diagram below, check the AVC-LAN circuit between the navigation receiver and the component which has stored this code.

    1. Disconnect all connectors between the navigation receiver and the component which has stored this code.



    2. Check for an open or short in the AVC-LAN circuit between the navigation receiver and the component which has stored this code.

      OK:
      There is no open or short circuit.


      E138055E05


      E145835E05



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE NAVIGATION RECEIVER ASSEMBLY
  1. Replace the navigation receiver assembly with a normal one (Click here).

  1. Check if the same problem occurs again.

    OK:
    Same problem does not occur.



NG
REPLACE COMPONENT WHICH HAS STORED THIS CODE
OK

END