Home › Engine / Hybrid System · 2UZ-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the ignition switch is turned ON, the battery voltage is applied to the IGSW of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the integration relay (EFI MAIN relay) and supplying power to either terminal +B or +B2 of the ECM.

WIRING DIAGRAM


A164739E06


INSPECTION PROCEDURE

1.INSPECT FUSES (AM2, IG2 MAIN, EFI NO. 1 AND IGN)
A162323E01
  1. Remove the AM2 fuse, IG2 MAIN fuse, EFI NO. 1 fuse and IGN fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    AM2 fuse
    Always
    Below 1 Ω
    IG2 MAIN fuse
    Always
    Below 1 Ω
    EFI NO. 1 fuse
    Always
    Below 1 Ω
    IGN fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


2.INSPECT INTEGRATION RELAY (IG2, EFI MAIN)
A148742E04
  1. Remove the integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1C-1 - 1B-8
    When battery voltage not applied
    10 kΩ or higher
    When battery voltage applied to terminals 1B-6 and 1B-7
    Below 1 Ω
    1C-1 - 1B-4
    When battery voltage not applied
    10 kΩ or higher
    When battery voltage applied to terminals 1B-2 and 1B-3
    Below 1 Ω



NG
REPLACE INTEGRATION RELAY
OK


3.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
A136305E57
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D56-81 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT ECM (IGSW VOLTAGE)
A164740E07
  1. Disconnect the ECM connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A27-28 (IGSW) - D56-81 (E1)
    Ignition switch ON
    11 to 14 V

    Result 
    Result
    Proceed to
    Outside standard range
    A
    Within standard range
    B



B
REPLACE ECM (Click here)
A


5.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM, IGNITION SWITCH, BATTERY)
A162324E03
  1. Disconnect the ECM connector.

  1. Disconnect the ignition switch connector.

  1. Disconnect the cable from the battery positive (+) terminal.

  1. Remove the AM2 fuse and integration relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A27-28 (IGSW) - 1B-8
    Always
    Below 1 Ω
    1B-7 - Body ground
    Always
    Below 1 Ω
    Positive (+) battery cable - 1C-1
    Always
    Below 1 Ω
    Positive (+) battery cable - AM2 fuse terminal 1
    Always
    Below 1 Ω
    H10-5 (AM2) - AM2 fuse terminal 2
    Always
    Below 1 Ω
    H10-6 (IG2) - 1B-6
    Always
    Below 1 Ω
    A27-28 (IGSW) or 1B-8 - Body ground
    Always
    10 kΩ or higher
    Positive (+) battery cable or AM2 fuse terminal 1 - Body ground
    Always
    10 kΩ or higher
    Positive (+) battery cable or 1C-1 - Body ground
    Always
    10 kΩ or higher
    H10-5 (AM2) or AM2 fuse terminal 2 - Body ground
    Always
    10 kΩ or higher
    H10-6 (IG2) or 1B-6 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT IGNITION SWITCH
B110407E09
  1. Disconnect the ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (AM2) - 7 (ST2)
    Ignition switch position START
    Below 1 Ω
    Except above
    10 kΩ or higher



NG
REPLACE IGNITION SWITCH (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM, BATTERY AND BODY GROUND)
A162325E05
  1. Disconnect the ECM connector.

  1. Disconnect the cable from the battery positive terminal.

  1. Remove the integration relay from the engine room relay block.

  1. Disconnect the integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A27-3 (+B) - 1B-4
    Always
    Below 1 Ω
    A27-2 (+B2) - 1B-4
    Always
    Below 1 Ω
    A27-34 (MREL) - 1B-2
    Always
    Below 1 Ω
    1C-1 - Positive (+) battery cable
    Always
    Below 1 Ω
    1B-3 - Body ground
    Always
    Below 1 Ω
    A27-3 (+B) or 1B-4 - Body ground
    Always
    10 kΩ or higher
    A27-2 (+B2) or 1B-4 - Body ground
    Always
    10 kΩ or higher
    A27-34 (MREL) or 1B-2 - Body ground
    Always
    10 kΩ or higher
    1C-1 or Positive (+) battery cable - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE ENGINE ROOM RELAY BLOCK