SFI SYSTEM > Cranking Holding Function Circuit |


| 1.READ VALUE USING TECHSTREAM (STARTER SIGNAL) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.
Check the result when the ignition switch is turned to ON and START positions.
| Ignition Switch Condition | Starter Signal |
| ON | OFF |
| START | ON |
| Result | Proceed to |
| Outside standard range | A |
| Within standard range | B |
|
| ||||
| A | |
| 2.INSPECT ECM (STSW TERMINAL VOLTAGE) |
![]() |
Disconnect the ECM connector.
Perform the cranking operation.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A27-14 (STSW) - Body ground | ON | Below 1 V |
| START | 9 to 13 V |
|
| ||||
| OK | |
| 3.INSPECT ECM (STAR TERMINAL OUTPUT VOLTAGE) |
![]() |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Powertrain / Engine / Active Test / Control the All Cylinders Fuel Cut.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 6 (Junction Connector) - Body ground | Ignition switch ON (shift lever in P or N) | Below 1 V |
| Ignition switch ON (shift lever not in P or N) | 9 to 13 V | |
| Cranking operation | 9 to 13 V |
|
| ||||
| OK | |
| 4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Disconnect the Park/Neutral Position (PNP) switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Shift Lever Position | Specified Condition |
| 2-6, 4-5 | P | Below 1 Ω |
| 1-2 | R | |
| 2-9, 4-5 | N | |
| 2-7 | D | |
| 2-7 | S | |
| Except above terminals | All Positions | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (PNP SWITCH - ECM) |
![]() |
Disconnect the PNP switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D21-4 - D56-16 (STAR) | Always | Below 1 Ω |
| D21-4 - D56-120 (NSW) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (PNP SWITCH - ECM - ST RELAY) |
![]() |
Remove the ST relay from the engine room relay block.
Disconnect the PNP switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D21-5 - A27-46 (STA) | Always | Below 1 Ω |
| D21-5 - 1 (ST relay) | Always | Below 1 Ω |
| 2 (ST relay) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 7.INSPECT IGNITION SWITCH |
![]() |
Remove the ignition switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| All terminals | LOCK | 10 kΩ or higher |
| 2 (ACC) - 4 (AM1) | ACC | Below 1 Ω |
| 1 (IG1) - 2 (ACC) - 4 (AM1) | ON | |
| 5 (AM2) - 6 (IG2) | ||
| 1 (IG1) - 3 (ST1) - 4 (AM1) | START | |
| 5 (AM2) - 6 (IG2) - 7 (ST2) |
|
| ||||
| OK | ||
| ||
| 8.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Disconnect the PNP switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Shift Lever Position | Specified Condition |
| 2-6, 4-5 | P | Below 1 Ω |
| 1-2 | R | |
| 2-9, 4-5 | N | |
| 2-7 | D | |
| 2-7 | S | |
| Except above terminals | All Positions | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (PNP SWITCH - IGNITION SWITCH AND ECM) |
![]() |
Disconnect the ignition switch connector.
Disconnect the PNP switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H10-7 (ST2) - D21-4 | Always | Below 1 Ω |
| D56-16 (STAR) - D21-4 | Always | |
| D56-120 (NSW) - D21-4 | Always | |
| H10-7 (ST2) or D21-4 - Body ground | Always | 10 kΩ or higher |
| D56-16 (STAR) or D21-4 - Body ground | Always | |
| D56-120 (NSW) or D21-4 - Body ground | Always |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (PNP SWITCH - ECM - ST RELAY) |
![]() |
Remove the ST relay from the engine room relay block.
Disconnect the PNP switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D21-5 or A27-46 (STA) - Body ground | Always | 10 kΩ or higher |
| D21-5 or 1 (ST relay) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||