Home › Engine / Hybrid System · 3UR-FBE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > Cranking Holding Function Circuit

for Preparation Click here


DESCRIPTION

The cranking holding control system keeps energizing the starter relay from when the ECM detects the starter signal (STSW signal) from the ignition switch until the ECM performs a judgment of "Engine started". Furthermore, the ECM outputs an accessory cut signal (ACCR signal) to the ACC cut relay during cranking to prevent flickering of the combination meter, clock, audio system, and so on.
When the ECM detects the STSW signal, the ECM outputs the starter relay drive signal (STAR signal) to the starter relay through the park/neutral position switch, and then, the engine is cranked. When the ECM receives a stable engine speed signal (NE signal), more specifically, when the NE signal reaches a predetermined value, the ECM stops outputting the STAR signal.
Also, the ECM monitors the starter relay operating conditions based on the STA terminal voltage status.

A169043E01


WIRING DIAGRAM


A185042E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

  1. Check the result when the ignition switch is turned to ON and START positions.

    OK:
    Ignition Switch Condition
    Starter Signal
    ON
    OFF
    START
    ON

    Result 
    Result
    Proceed to
    Outside standard range
    A
    Within standard range
    B



B
Go to step 2
A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT ECM (STSW TERMINAL VOLTAGE)
A164014E05
  1. Disconnect the ECM connector.

  1. Perform the cranking operation.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A27-14 (STSW) - Body ground
    ON
    Below 1 V
    START
    9 to 13 V

HINT:
DTCs related to the communication with other computers may be set due to this inspection. Clear those DTCs after the inspection.



NG
Go to step 7
OK


3.INSPECT ECM (STAR TERMINAL OUTPUT VOLTAGE)
A185037E03
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the All Cylinders Fuel Cut.

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
6 (Junction Connector) - Body ground
Ignition switch ON (shift lever in P or N)
Below 1 V
Ignition switch ON (shift lever not in P or N)
9 to 13 V
Cranking operation
9 to 13 V

HINT:
  1. The junction connector is in the engine room connector holder block as the illustration above.
  2. During this inspection, all connectors and relays should be connected.



NG
Go to step 8
OK


4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
A185041E01
  1. Disconnect the Park/Neutral Position (PNP) switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Shift Lever Position
    Specified Condition
    2 - 6, 4 - 5
    P
    Below 1 Ω
    1 - 2
    R
    2 - 9, 4 - 5
    N
    2 - 7
    D
    2 - 7
    S
    Except above terminals
    All Positions
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (PNP SWITCH - ECM)
A172525E04
  1. Disconnect the PNP switch connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D21-4 - D56-16 (STAR)
    Always
    Below 1 Ω
    D21-4 - D56-120 (NSW)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (PNP SWITCH - ECM - ST RELAY)
A185039E01
  1. Remove the ST relay from the engine room relay block.

  1. Disconnect the PNP switch connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D21-5 - A27-46 (STA)
    Always
    Below 1 Ω
    D21-5 - 1 (ST relay)
    Always
    Below 1 Ω
    2 (ST relay) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE STARTER CIRCUIT (STARTER - ST RELAY) 

7.INSPECT IGNITION SWITCH
A107906E10
  1. Remove the ignition switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    All terminals
    LOCK
    10 kΩ or higher
    2 (ACC) - 4 (AM1)
    ACC
    Below 1 Ω
    1 (IG1) - 2 (ACC) - 4 (AM1)
    ON
    5 (AM2) - 6 (IG2)
    1 (IG1) - 3 (ST1) - 4 (AM1)
    START
    5 (AM2) - 6 (IG2) - 7 (ST2)



NG
REPLACE IGNITION SWITCH (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - ECM) 

8.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
A185041E01
  1. Disconnect the PNP switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Shift Lever Position
    Specified Condition
    2 - 6, 4 - 5
    P
    Below 1 Ω
    1 - 2
    R
    2 - 9, 4 - 5
    N
    2 - 7
    D
    2 - 7
    S
    Except above terminals
    All Positions
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (PNP SWITCH - IGNITION SWITCH AND ECM)
A185038E01
  1. Disconnect the ignition switch connector.

  1. Disconnect the PNP switch connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance :
    Tester Connection
    Condition
    Specified Condition
    H10-7 (ST2) - D21-4
    Always
    Below 1 Ω
    D56-16 (STAR) - D21-4
    Always
    D56-120 (NSW) - D21-4
    Always
    H10-7 (ST2) or D21-4 - Body ground
    Always
    10 kΩ or higher
    D56-16 (STAR) or D21-4 - Body ground
    Always
    D56-120 (NSW) or D21-4 - Body ground
    Always

    HINT:
    The wire between the PNP switch and the ignition switch has a diode (refer to the wiring diagram). The current flowing to the PNP switch is rectified by the diode.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK HARNESS AND CONNECTOR (PNP SWITCH - ECM - ST RELAY)
A185039E01
  1. Remove the ST relay from the engine room relay block.

  1. Disconnect the PNP switch connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D21-5 or A27-46 (STA) - Body ground
    Always
    10 kΩ or higher
    D21-5 or 1 (ST relay) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)