DTC C1249/49 Open in Stop Light Switch Circuit |
| DTC Code | DTC Detection Condition | Trouble Area |
| C1249/49 | When one of following conditions is met:
|
|

| 1.READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Select the Data List mode on the Techstream.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| STOP Light SW | Stop light switch / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
|
| ||||
| OK | |
| 2.RECONFIRM DTC |
Clear the DTC (Click here).
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||
| 3.INSPECT FUSE (STOP) |
![]() |
Remove the STOP fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| STOP fuse | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.INSPECT STOP LIGHT CONTROL RELAY (BRK NO. 1, BRK NO. 2) |
![]() |
Remove the stop light control relays (BRK NO. 1 and BRK NO. 2) from the engine room relay block.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 4 | When battery voltage is not applied to terminals 1 and 2 | Below 1 Ω |
| 3 - 5 | When battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 4 | When battery voltage is applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | When battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| 3 - 4 | When battery voltage is not applied to terminals 1 and 2 | Below 1 Ω |
| When battery voltage is applied to terminals 1 and 2 | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.INSPECT STOP LIGHT SWITCH ASSEMBLY |
![]() |
Disconnect the A4 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - 2 | Pin not pushed | Below 1 Ω |
| Pin pushed | 10 kΩ or higher | |
| 3 - 4 | Pin not pushed | |
| Pin pushed | Below 1 Ω |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (BATTERY - SKID CONTROL ECU) |
![]() |
Disconnect the A19 ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A19-11 (STP2) - Body ground | Brake pedal depressed | 8 to 14 V |
| A19-11 (STP2) - Body ground | Brake pedal released | Below 4.0 V |
| A19-41 (STP) - Body ground | Brake pedal depressed | 8 to 14 V |
| A19-41 (STP) - Body ground | Brake pedal released | Below 4.0 V |
|
| ||||
| OK | ||
| ||