Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM (w/o AVS)

DTC    C1782    Power Source Voltage Malfunction

for Preparation Click here


DESCRIPTION

  1. This circuit provides power to operate the suspension control ECU.
  2. The suspension control ECU, controlling the air suspension system, is activated when the ignition switch is turned ON. The main relay inside the ECU is activated after 2 seconds and the system is operated by +B power source.

DTC Code
Detection Condition
Trouble Area
C1782
Terminal IG, B or BAT voltage is 10 V or less, or 16 V or more for 0.5 seconds
  1. Battery
  2. Wire harness or connector
  3. Suspension control ECU

WIRING DIAGRAM


C179506E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (POWER SOURCE VOLTAGE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and turn the Techstream main switch on.

  1. Enter the following menus: Chassis / Air suspension / Data List.

    Air Suspension 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    +B Power Source Voltage
    ECU power supply voltage / min.: 0 V, max.: 25.5 V
    Actual battery power supply voltage: 11 to 14 V
    -
    IG Power Source Voltage
    ECU power supply voltage / min.: 0 V, max.: 25.5 V
    Actual ECU power supply voltage: 11 to 14 V
    -

    Standard voltage:
    11 to 14 V

    Result 
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to the Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC Chart)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


2.INSPECT FUSE (AIR SUS, AIR SUS NO. 2, ECU-IG NO. 2)


    E160630E08
  1. Remove the AIR SUS No. 2 and AIR SUS fuses from the engine room relay block.

  1. Remove the ECU-IG No. 2 fuse from the cowl side junction block LH.

  1. Measure the resistance of the AIR SUS, AIR SUS No. 2 and ECU-IG No. 2 fuses.

    Standard Resistance:
    Fuse
    Condition
    Specified Condition
    AIR SUS No. 2
    Always
    Below 1 Ω
    AIR SUS
    Always
    Below 1 Ω
    ECU-IG No. 2
    Always
    Below 1 Ω

  1. Reinstall the AIR SUS, AIR SUS No. 2 and ECU-IG No. 2 fuses.



NG
REPLACE FUSE
OK


3.CHECK BATTERY VOLTAGE


    C179507E01
  1. Disconnect the O19 ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O19-24 (B) - Body ground
    Always
    11 to 14 V
    O19-25 (BAT) - Body ground
    Always
    11 to 14 V
    O19-10 (IG) - Body ground
    Ignition switch ON
    11 to 14 V



NG
BATTERY VOLTAGE IS LOW OR CHARGING SYSTEM HAS MALFUNCTION
OK


4.CHECK FOR DTC
  1. Clear the DTC (Click here).

  1. Check for DTC (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPLACE SUSPENSION CONTROL ECU (Click here)
A

END