DTC C1761 Continuous Electric Current to Height Control Compressor Motor |
| DTC Code | Detection Condition | Trouble Area |
| C1761*1 | With the AIR SUS relay activated, the vehicle does not go up to the standard vehicle height after 90 seconds have elapsed. |
|

| 1.INSPECT FOR AIR LEAK |
Check for air leakage .
|
| ||||
| OK | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (EXHAUST SOLENOID) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON, and turn the Techstream main switch on.
Enter the following menus: Chassis / Air suspension / Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Exhaust Solenoid | Exhaust solenoid valve | ON or OFF | Operation sound of solenoid (clicking sound) can be heard |
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING TECHSTREAM (REAR GATE SOLENOID) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON, and turn the Techstream main switch on.
Enter the following menus: Chassis / Air suspension / Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Rear Gate Solenoid | Gate solenoid valve/ | ON or OFF | Operation sound of solenoid (clicking sound) can be heard |
|
| ||||
| OK | |
| 4.PERFORM ACTIVE TEST USING TECHSTREAM (REAR LEVELING SOLENOID) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON, and turn the Techstream main switch on.
Enter the following menus: Chassis / Air suspension / Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Rear Leveling Solenoid | Leveling solenoid valve | ON or OFF | Operation sound of solenoid (clicking sound) can be heard |
|
| ||||
| OK | |
| 5.INSPECT SUSPENSION CONTROL RELAY (AIR SUS) |
![]() |
Turn the ignition switch off.
Remove the AIR SUS relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | When 12 V battery voltage is not applied to terminal 1 and 2 | 10 kΩ or higher |
| When 12 V battery voltage is applied to terminal 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (COMPRESSOR - BATTERY AND BODY GROUND) |
![]() |
Remove the AIR SUS relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Relay block AIR SUS relay terminal 5 - Body ground | Always | 11 to 14 V |
Disconnect the Q7 compressor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Relay block AIR SUS relay terminal 3 - Q7-1 (B) | Always | Below 1 Ω |
| Relay block AIR SUS relay terminal 3 or Q7-1 (B) - Body ground | Always | 10 kΩ or higher |
| Q7-2 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 7.CHECK VEHICLE HEIGHT |
Check the vehicle height (Click here).
|
| ||||
| OK | |
| 8.CHECK FOR DTC |
Clear the DTC (Click here).
Check for DTC (Click here).
| Result | Proceed to |
| DTC is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||