FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) > One or more Power Seat Motors do not Operate |

| 1.READ VALUE USING TECHSTREAM (FRONT POWER SEAT SWITCH) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Body Electrical / Driver seat / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Reclining Rear | Reclining switch signal (Rearward) / ON or OFF | ON: Reclining switch (Rearward) on OFF: Reclining switch (Rearward) off | - |
| Reclining Front | Reclining switch signal (Forward) / ON or OFF | ON: Reclining switch (Forward) on OFF: Reclining switch (Forward) off | - |
| Front Vertical Down | Front vertical switch signal (Downward) / ON or OFF | ON: Front vertical switch (Downward) on OFF: Front vertical switch (Downward) off | - |
| Front Vertical Up | Front vertical switch signal (Upward) / ON or OFF | ON: Front vertical switch (Upward) on OFF: Front vertical switch (Upward) off | - |
| Lifter Switch Down | Lifter switch signal (Downward) / ON or OFF | ON: Lifter switch (Downward) on OFF: Lifter switch (Downward) off | - |
| Lifter Switch Up | Lifter switch signal (Upward) / ON or OFF | ON: Lifter switch (Upward) on OFF: Lifter switch (Upward) off | - |
| Slide Rear | Sliding switch signal (Rearward) / ON or OFF | ON: Sliding switch (Rearward) on OFF: Sliding switch (Rearward) off | - |
| Slide Front | Sliding switch signal (Forward) / ON or OFF | ON: Sliding switch (Forward) on OFF: Sliding switch (Forward) off | - |
|
| ||||
| OK | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (POWER SEAT MOTOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Body Electrical / Driver Seat / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Seat Reclining | Seat reclining operation | Front/OFF/Rear | - |
| Front Vertical Operation | Seat front vertical operation | Up/OFF/Down | - |
| Lifter Operation | Seat lifter operation | Up/OFF/Down | - |
| Seat Slide Operation | Seat sliding operation | Front/OFF/Rear | - |
|
| ||||
| OK | ||
| ||
| 3.INSPECT FRONT SEAT ASSEMBLY LH (POWER SEAT MOTOR) |
Remove the front seat assembly LH (Click here).
Check operation of the sliding motor.
![]() |
Check if the seat moves smoothly when the battery is connected to the sliding motor connector terminals.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 1 Battery negative (-) → 2 | Forward |
| Battery positive (+) → 2 Battery negative (-) → 1 | Rearward |
Check operation of the reclining motor.
![]() |
Check if the seat moves smoothly when the battery is connected to the reclining motor connector terminals.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 2 Battery negative (-) → 1 | Forward |
| Battery positive (+) → 1 Battery negative (-) → 2 | Rearward |
Check operation of the front vertical motor.
![]() |
Check if the seat moves smoothly when the battery is connected to the front vertical motor connector terminals.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 1 Battery negative (-) → 2 | Upward |
| Battery positive (+) → 2 Battery negative (-) → 1 | Downward |
Check operation of the lifter motor.
![]() |
Check if the seat moves smoothly when the battery is connected to the lifter motor connector terminals.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 2 Battery negative (-) → 1 | Upward |
| Battery positive (+) → 1 Battery negative (-) → 2 | Downward |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - POWER SEAT MOTOR) |
![]() |
Disconnect the X10 switch connector.
Disconnect the X5, X6, X7 and X8 motor connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| X10-2 (SLD+) - X5-1 | Always | Below 1 Ω |
| X10-2 (SLD+) or X5-1 - Body ground | Always | 10 kΩ or higher |
| X10-3 (SLD-) - X5-2 | Always | Below 1 Ω |
| X10-3 (SLD-) or X5-2 - Body ground | Always | 10 kΩ or higher |
| X10-4 (FRV-) - X6-2 | Always | Below 1 Ω |
| X10-4 (FRV-) or X6-2 - Body ground | Always | 10 kΩ or higher |
| X10-6 (FRV+) - X6-1 | Always | Below 1 Ω |
| X10-6 (FRV+) or X6-1 - Body ground | Always | 10 kΩ or higher |
| X10-7 (LFT+) - X7-2 | Always | Below 1 Ω |
| X10-7 (LFT+) or X7-2 - Body ground | Always | 10 kΩ or higher |
| X10-8 (RCL+) - X8-2 | Always | Below 1 Ω |
| X10-8 (RCL+) or X8-2 - Body ground | Always | 10 kΩ or higher |
| X10-9 (LFT-) - X7-1 | Always | Below 1 Ω |
| X10-9 (LFT-) or X7-1 - Body ground | Always | 10 kΩ or higher |
| X10-10 (RCL-) - X8-1 | Always | Below 1 Ω |
| X10-10 (RCL-) or X8-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||