Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM

DTC    B2799    Engine Immobiliser System Malfunction

for Preparation Click here


DESCRIPTION

This DTC is output when one of the following occurs: 1) the ECM detected errors in its own communications with the transponder key ECU; 2) the ECM detects errors in the communication lines: or 3) the ECU - ECM communication ID between the transponder key ECU and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no engine immobiliser DTCs are present. If present, troubleshoot the engine immobiliser DTCs first.

DTC Code
DTC Detection Condition
Trouble Area
B2799
  1. When the ignition is ON and a communication error or communication line error occurs between the engine ECU (engine control computer) and the ID code box (immobiliser code computer) for 6 seconds.
  2. When the ignition is ON and the engine ECU receives a different communication ID for 6 seconds.
  1. Harness or connector
  2. Transponder key ECU
  3. ECM

WIRING DIAGRAM


B168146E04


INSPECTION PROCEDURE

HINT:
When the transponder key ECU and/or ECM is replaced, reregister the ECU - ECM communication ID .

1.CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTC (Click here).

    OK:
    B2799 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.REREGISTER ECU - ECM COMMUNICATION ID
  1. Reregister the ECU - ECM communication ID .


NEXT


4.CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


5.CHECK FOR DTC
  1. Check for DTC (Click here).

    OK:
    DTC B2799 is not output.



NG
Go to step 6
OK

END 

6.CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch off.

  1. Check that the connectors are properly connected to the ECM and the transponder key ECU.

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTOR CORRECTLY
OK


7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
B129773E06
  1. Disconnect the H32 ECU connector.

  1. Disconnect the A27 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H32-13 (EFIO) - A27-40 (IMI)
    Always
    Below 1 Ω
    H32-12 (EFII) - A27-29 (IMO)
    H32-13 (EFIO) or A27-40 (IMI) - Body ground
    Always
    10 kΩ or higher
    H32-12 (EFII) or A27-29 (IMO) - Body ground

  1. Reconnect the ECU and ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.REPLACE TRANSPONDER KEY ECU
  1. Temporarily replace the transponder key ECU with a new or normally functioning one (Click here).


NEXT


9.CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


10.CHECK FOR DTC
  1. Check for DTC (Click here).
    Result 
    Result
    Proceed to
    DTC B2799 is not output
    A
    DTC B2799 is output (for 2UZ-FE)
    B
    DTC B2799 is output (for 3UR-FE)
    C
    DTC B2799 is output (for 3UR-FBE)
    D



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)
A

END (TRANSPONDER KEY ECU IS DEFECTIVE)