Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM

WIRELESS DOOR LOCK CONTROL SYSTEM > Only Wireless Control Function is Inoperative

for Preparation Click here


DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher relay signals to the turn signal flasher relay (hazard warning lights).

WIRING DIAGRAM


B176381E06


INSPECTION PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
  1. Check the wireless door lock control system function (Click here).

Result 
Result
Proceed to
The wireless door LOCK/UNLOCK function does not operate with transmitter
A
The power back door function does not operate with transmitter
B


B
GO TO POWER BACK DOOR SYSTEM (Click here)
A


2.CHECK DOOR CONTROL TRANSMITTER
  1. When another registered door control transmitter is used, check that the wireless operates normally.
    Result 
    Result
    Proceed to
    Wireless door LOCK/UNLOCK function operates and door control transmitter that did not operate is electrical key transmitter
    A
    Wireless door LOCK/UNLOCK function does not operate
    B



B
Go to step 4
A


3.INSPECT TRANSMITTER BATTERY (VOLTAGE)


  1. Electrical key transmitter



      B178434
    1. Remove the battery from the electrical key transmitter that does not operate. Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal (Click here).

      NOTICE:
      Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.

    2. Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.



    3. B194372E02
    4. Using an oscilloscope, check the transmitter battery voltage waveform.

      HINT:
      Measure the transmitter battery voltage while pressing the LOCK or UNLOCK switch on the transmitter.

      Standard Voltage:
      Item
      Content
      Tester Connection
      Battery positive (+) - Battery negative (-)
      Tool Setting
      0.5 V/DIV., 100 ms/DIV.
      Condition
      Ignition switch OFF, all doors closed and lock switch pushed
      Specified Condition
      2.2 to 3.2 V (Refer to the waveform)



NG
REPLACE TRANSMITTER BATTERY (Click here)
OK

REPLACE DOOR CONTROL TRANSMITTER 

4.CHECK ROOM LIGHT ASSEMBLY
  1. Check that the room light illumination operates normally.

    OK:
    Room light operation normally.



NG
Go to LIGHTING SYSTEM (Click here)
OK


5.SWITCH TO SELF-DIAGNOSTIC MODE


    B110075E20
  1. Switch to self-diagnostic mode by operating the ignition key cylinder.

    1. Make sure the vehicle is in its initial condition. Then insert the key into the ignition key cylinder and remove it.

    2. Within 5 seconds of removing the key, insert the key into the ignition key cylinder (ignition switch off). Then turn the ignition switch to ON and off.

    3. Within 30 seconds of turning the ignition switch off, perform the following operation 9 times: turn the ignition switch to ON and then off.

      NOTICE:
      If the system cannot enter self-diagnostic mode, the system returns to normal mode.

      HINT:
      1. Turning the ignition switch to ON after the above operations have been completed ends self-diagnostic mode.
      2. Do not lock or unlock doors during self-diagnostic mode.

  1. Check that the system has switched to self-diagnostic mode by checking the room light flash pattern.

    OK:
    Flash pattern is same as illustration.



NG
Go to step 12
OK


6.CHECK BY SELF DIAGNOSTIC MODE

B123864E03

  1. Inspect the diagnosis outputs when the door control transmitter switch is held down. The diagnosis outputs can be checked by the flash patterns of the room light.

    Result 
    Result
    Proceed to
    Unmatching recognition code is output
    A
    Normal waves (light flash patterns) is output
    B
    No diagnosis outputs
    C



B
REPLACE MAIN BODY ECU

C
Go to step 8
A


7.REGISTER RECOGNITION CODE
  1. Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered (Click here).

    OK:
    Recognition code can be registered.



NG
Go to step 15
OK

END 

8.CHECK DOOR CONTROL RECEIVER (RESPONSE)
  1. Prepare the door control transmitter of another vehicle.

  1. Hold down the door control transmitter switch.

  1. Check that an unmatching recognition code is output.

    OK:
    Unmatching recognition code is output.



NG
Go to step 9
OK

REPLACE DOOR CONTROL TRANSMITTER 

9.REPLACE DOOR CONTROL RECEIVER
  1. Temporarily replace the door lock control receiver with a new or normally functioning one (Click here).


NEXT


10.REGISTER RECOGNITION CODE
  1. Perform the registration procedures (Click here).


NEXT


11.CHECK DOOR CONTROL RECEIVER (OPERATION)
  1. Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.

    OK:
    Doors can be locked and unlocked with transmitter.



NG
REPLACE MAIN BODY ECU
OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE) 

12.INSPECT UNLOCK WARNING SWITCH


    B164411E03
  1. Remove the unlock warning switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Free
    10 kΩ or higher
    Pushed
    Below 1 Ω

  1. Reconnect the unlock warning switch.



NG
REPLACE UNLOCK WARNING SWITCH (Click here)
OK


13.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - MAIN BODY ECU AND BODY GROUND)
B191759E01
  1. Disconnect the H21 unlock warning switch connector.

  1. Disconnect the H1 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H21-1 - H1-5 (KSW)
    Always
    Below 1 Ω
    H21-2 - Body ground
    H1-5 (KSW) or H21-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the unlock warning switch connector.

  1. Reconnect the main body ECU connector



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.INSPECT DOOR CONTROL RECEIVER (OUTPUT)


    B175270E03
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O25-2 (RDA) - Body ground
    Transmitter switch ON → OFF (No key in ignition key cylinder, all doors closed)
    Below 1 V → 6 to 7 V → Below 1 V



NG
Go to step 15
OK

REPLACE MAIN BODY ECU 

15.REPLACE DOOR CONTROL TRANSMITTER
  1. Temporarily replace the door control transmitter module with a new or normally functioning one.


NEXT


16.REGISTER RECOGNITION CODE
  1. Perform the registration procedures (Click here).


NEXT


17.CHECK DOOR CONTROL TRANSMITTER MODULE
  1. Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.

    OK:
    Doors can be locked and unlocked with transmitter.



NG
REPLACE DOOR CONTROL RECEIVER (Click here)
OK

END (DOOR CONTROL TRANSMITTER MODULE IS DEFECTIVE)