Home › Audio/Visual/Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Speaker Circuit (Independent Amplifier)

for Preparation Click here


DESCRIPTION

The stereo component amplifier assembly sends sound signals to the speaker.

WIRING DIAGRAM


E173185E01


E160611E01


INSPECTION PROCEDURE

1.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area
    B



B
Go to step 11
A


2.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Front No. 1 speaker assembly
    A
    Front No. 2 speaker assembly
    B
    Front No. 3 speaker assembly
    C
    Front No. 4 speaker assembly
    D



B
Go to step 5

C
Go to step 7

D
Go to step 9
A


3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E144966E22
  1. Disconnect the L8*1 and M10*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.8 to 2.6 Ω

  1. Reconnect the speaker connectors.



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 1 SPEAKER)


    E160615E01
  1. Disconnect the L8*1 and M10*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Disconnect the I18 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    I18-1 (WFL+) - M10-1
    Always
    Below 1 Ω
    I18-5 (WFL-) - M10-2
    I18-1 (WFL+) - Body ground
    Always
    10 kΩ or higher
    I18-5 (WFL-) - Body ground
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    I18-2 (WFR+) - L8-1
    Always
    Below 1 Ω
    I18-6 (WFR-) - L8-2
    I18-2 (WFR+) - Body ground
    Always
    10 kΩ or higher
    I18-6 (WFR-) - Body ground

  1. Reconnect the speaker connector.

  1. Reconnect the stereo component amplifier assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

5.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E144969E20
  1. Disconnect the I10*1 and I12*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWL+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWL-)
    3 (TWL+) - 4 (TWL-)
    Always
    1.5 to 2.5 Ω
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWR+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWR-)
    3 (TWR+) - 4 (TWR-)
    Always
    1.5 to 2.5 Ω

  1. Reconnect the speaker connector.



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER)


    E160616E01
  1. Disconnect the I19 stereo component amplifier assembly connector.

  1. Disconnect the I10*1 and I12*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    I19-3 (FL+) - I12-3 (TWL+)
    Always
    Below 1 Ω
    I19-8 (FL-) - I12-4 (TWL-)
    I19-3 (FL+) - Body ground
    Always
    10 kΩ or higher
    I19-8 (FL-) - Body ground
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    I19-10 (FR+) - I10-3 (TWR+)
    Always
    Below 1 Ω
    I19-9 (FR-) - I10-4 (TWR-)
    I19-10 (FR+) - Body ground
    Always
    10 kΩ or higher
    I19-9 (FR-) - Body ground

  1. Reconnect the stereo component amplifier assembly connector.

  1. Reconnect the speaker connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

7.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    E160614E05
  1. Disconnect the L1*1 and M1*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Always
    3.0 to 4.2 Ω

  1. Reconnect the speaker connector.



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 3 SPEAKER)


    E146500E02
  1. Disconnect the L1*1, M1*2, I10*1 and I12*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    I12-1 (+) - M1-3
    Always
    Below 1 Ω
    I12-2 (-) - M1-1
    I12-1 (+) - Body ground
    Always
    10 kΩ or higher
    I12-2 (-) - Body ground
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    I10-1 (+) - L1-3
    Always
    Below 1 Ω
    I10-2 (-) - L1-1
    I10-1 (+) - Body ground
    Always
    10 kΩ or higher
    I10-2 (-) - Body ground

  1. Reconnect the speaker connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)  

9.INSPECT FRONT NO. 4 SPEAKER ASSEMBLY


    E146506E07
  1. Disconnect the I14 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω

  1. Reconnect the speaker connector.



NG
REPLACE FRONT NO. 4 SPEAKER ASSEMBLY (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 4 SPEAKER)


    E160617E01
  1. Disconnect the I14 speaker connector.

  1. Disconnect the I18 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I18-3 (CTR+) - I14-1
    Always
    Below 1 Ω
    I18-9 (CTR-) - I14-2
    I18-3 (CTR+) - Body ground
    Always
    10 kΩ or higher
    I18-9 (CTR-) - Body ground

  1. Reconnect the speaker connector.

  1. Reconnect the stereo component amplifier assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

11.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Rear No. 2 speaker assembly
    A
    Rear No. 1 speaker assembly
    B
    Quarter side speaker assembly
    C
    w/ Box No. 1 speaker assembly
    D



B
Go to step 14

C
Go to step 16

D
Go to step 18
A


12.INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    E160614E10
  1. Disconnect the N2*1 and N8*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (-TW) - 3 (+TW)
    Always
    3.0 to 4.2 Ω
    1 (-TW) - 2 (-)
    Always
    Below 1 Ω
    3 (+TW) - 4 (+)

  1. Reconnect the speaker connectors.



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)
OK


13.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - REAR NO. 2 SPEAKER)


    E160618E01
  1. Disconnect the I19 stereo component amplifier assembly connector.

  1. Disconnect the N2*1 and N8*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    I19-4 (RL+) - N8-3 (+TW)
    Always
    Below 1 Ω
    I19-11 (RL-) - N8-1 (-TW)
    I19-4 (RL+) - Body ground
    Always
    10 kΩ or higher
    I19-11 (RL-) - Body ground
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    I19-5 (RR+) - N2-3 (+TW)
    Always
    Below 1 Ω
    I19-12 (RR-) - N2-1 (-TW)
    I19-5 (RR+) - Body ground
    Always
    10 kΩ or higher
    I19-12 (RR-) - Body ground

  1. Reconnect the stereo component amplifier assembly.

  1. Reconnect the speaker connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

14.INSPECT REAR NO. 1 SPEAKER ASSEMBLY


    E144966E23
  1. Disconnect the N1*1 and N7*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.8 to 2.6 Ω

  1. Reconnect the speaker connectors.



NG
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
OK


15.CHECK HARNESS AND CONNECTOR (REAR NO. 1 SPEAKER - REAR NO. 2 SPEAKER)


    E149222E02
  1. Disconnect the N1*1, N2*1, N7*2 and N8*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    N8-4 (+) - N7-1
    Always
    Below 1 Ω
    N8-2 (-) - N7-2
    N8-4 (+) - Body ground
    Always
    10 kΩ or higher
    N8-2 (-) - Body ground
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    N2-4 (+) - N1-1
    Always
    Below 1 Ω
    N2-2 (-) - N1-2
    N2-4 (+) - Body ground
    Always
    10 kΩ or higher
    N2-2 (-) - Body ground

  1. Reconnect the speaker connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)  

16.INSPECT QUARTER SIDE SPEAKER ASSEMBLY


    E146506E04
  1. Disconnect the O37*1 and O31*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.5 Ω

  1. Reconnect the speaker connectors.



NG
REPLACE QUARTER SIDE SPEAKER ASSEMBLY (Click here)
OK


17.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - QUARTER SIDE SPEAKER)


    E160621E01
  1. Disconnect the I18 and I19 stereo component amplifier assembly connectors.

  1. Disconnect the O37*1 and O31*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I19-2 (SR+) - O37-1 (+)
    Always
    Below 1 Ω
    I19-7 (SR-) - O37-2 (-)
    I18-8 (SL+) - O31-1 (+)
    I18-7 (SL-) - O31-2 (-)
    I19-2 (SR+) - Body ground
    Always
    10 kΩ or higher
    I19-7 (SR-) - Body ground
    I18-8 (SL+) - Body ground
    I18-7 (SL-) - Body ground

  1. Reconnect the stereo component amplifier assembly connectors.

  1. Reconnect the speaker connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

18.INSPECT W/ BOX NO.1 SPEAKER ASSEMBLY


    E160619E02
  1. Disconnect the O13 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (WF1+) - 2 (WF1-)
    Always
    Approx. 1.2 Ω
    3 (WF2+) - 4 (WF2-)
    Always
    Approx. 1.2 Ω

  1. Reconnect the speaker connector.



NG
REPLACE W/ BOX NO.1 SPEAKER ASSEMBLY (Click here)
OK


19.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - W/ BOX NO.1 SPEAKER)


    E160620E01
  1. Disconnect the I18 and I19 stereo component amplifier assembly connector.

  1. Disconnect the O13 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I19-1 (WF1+) - O13-1 (WF1+)
    Always
    Below 1 Ω
    I19-6 (WF1-) - O13-2 (WF1-)
    I18-4 (WF2+) - O13-3 (WF2+)
    I18-10 (WF2-) - O13-4 (WF2-)
    I19-1 (WF1+) - Body ground
    Always
    10 kΩ or higher
    I19-6 (WF1-) - Body ground
    I18-4 (WF2+) - Body ground
    I18-10 (WF2-) - Body ground

  1. Reconnect the stereo component amplifier assembly connectors.

  1. Reconnect the speaker connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)