Home › Audio/Visual/Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Speaker Circuit (Built-in Amplifier)

for Preparation Click here


DESCRIPTION

The stereo component amplifier assembly sends sound signals to the speaker.

WIRING DIAGRAM


E160622E01


INSPECTION PROCEDURE

1.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area
    B



B
Go to step 7
A


2.CHECK FRONT SIDE SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Front No. 2 speaker assembly
    A
    Front No. 1 speaker assembly
    B



B
Go to step 5
A


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E146506E05
  1. Disconnect the I11*1 and I13*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWL+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWL-)
    3 (TWL+) - 4 (TWL-)
    Always
    3.6 to 4.4 Ω
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWR+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWR-)
    3 (TWR+) - 4 (TWR-)
    Always
    3.6 to 4.4 Ω

  1. Reconnect the speaker connectors.



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    E146562E02
  1. Disconnect the I1 radio receiver assembly connector.

  1. Disconnect the I11*1 and I13*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    I1-2 (FL+) - I13-3 (TWL+)
    Always
    Below 1 Ω
    I1-6 (FL-) - I13-4 (TWL-)
    I1-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    I1-6 (FL-) - Body ground
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    I1-1 (FR+) - I11-3 (TWR+)
    Always
    Below 1 Ω
    I1-5 (FR-) - I11-4 (TWR-)
    I1-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    I1-5 (FR-) - Body ground

  1. Reconnect the radio receiver assembly connector.

  1. Reconnect the speaker connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)  

5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E144966E01
  1. Disconnect the L8*1 and M10*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3.2 to 4.8 Ω

  1. Reconnect the speaker connectors.



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)


    E108122E21
  1. Disconnect the L8*1, M10*2, I11*1 and I13*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    I13-1 (+) - M10-1
    Always
    Below 1 Ω
    I13-2 (-) - M10-2
    I13-1 (+) - Body ground
    Always
    10 kΩ or higher
    I13-2 (-) - Body ground
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    I11-1 (+) - L8-1
    Always
    Below 1 Ω
    I11-2 (-) - L8-2
    I11-1 (+) - Body ground
    Always
    10 kΩ or higher
    I11-2 (-) - Body ground

  1. Reconnect the speaker connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT NO.2 SPEAKER ASSEMBLY (Click here)  

7.CHECK REAR SIDE SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Quarter side speaker assembly
    A
    Rear No. 1 speaker assembly
    B



B
Go to step 10
A


8.INSPECT QUARTER SIDE SPEAKER ASSEMBLY


    E146506E06
  1. Disconnect the O37*1 and O31*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (+)
    Always
    Below 1 Ω
    2 (-) - 4 (-)
    1 (+) - 2 (-)
    Always
    3.6 to 4.4 Ω

  1. Reconnect the speaker connectors.



NG
REPLACE QUARTER SIDE SPEAKER ASSEMBLY (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - QUARTER SIDE SPEAKER ASSEMBLY)


    E160623E01
  1. Disconnect the I2 radio receiver assembly connector.

  1. Disconnect the O37*1 and O31*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    I2-2 (RL+) - O31-1(+)
    Always
    Below 1 Ω
    I2-6 (RL-) - O31-2(-)
    I2-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    I2-6 (RL-) - Body ground
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    I2-1 (RR+) - O37-1(+)
    Always
    Below 1 Ω
    I2-3 (RR-) - O37-2(-)
    I2-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    I2-3 (RR-) - Body ground

  1. Reconnect the radio receiver assembly connector.

  1. Reconnect the speaker connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)  

10.INSPECT REAR NO.1 SPEAKER ASSEMBLY


    E144966E21
  1. Disconnect the N1*1 and N7*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3.2 to 4.8 Ω

  1. Reconnect the speaker connectors.



NG
REPLACE REAR NO.1 SPEAKER ASSEMBLY (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (QUARTER SIDE SPEAKER ASSEMBLY - REAR NO.1 SPEAKER ASSEMBLY)


    E108122E24
  1. Disconnect the N1*1, N7*2, O37*1 and O31*2 speaker connectors.

    HINT:
    *1: for RH Side
    *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    O31-3 (+) - N7-1
    Always
    Below 1 Ω
    O31-4 (-) - N7-2
    O31-3 (+) - Body ground
    Always
    10 kΩ or higher
    O31-4 (-) - Body ground
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    O37-3 (+) - N1-1
    Always
    Below 1 Ω
    O37-4 (-) - N1-2
    O37-3 (+) - Body ground
    Always
    10 kΩ or higher
    O37-4 (-) - Body ground

  1. Reconnect the speaker connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)