Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM

REAR POWER SEAT CONTROL SYSTEM > Fold Seat Switch Circuit

for Preparation Click here


DESCRIPTION

When the fold seat switch is operated, a switch operation signal is sent to the fold seat control ECU. The ECU receives switch operation signals from each switch and activates the No. 1 power seat motor and No. 2 power seat motor.

WIRING DIAGRAM


B195047E02


INSPECTION PROCEDURE

1.CHECK FOLD SEAT CONTROL ECU (FOLD SEAT SWITCH SIGNAL)


  1. Check the No. 1 fold seat switch signal.



      B193667E02
    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      LH Side 
      Tester Connection
      Condition
      Specified Condition
      O34-15 (RTRN) - Body ground
      Back door open
      No. 1 fold seat switch LH OFF
      11 to 14 V
      Back door open
      No. 1 fold seat switch LH return
      Below 1 V
      O34-16 (FOLD) - Body ground
      Back door open
      No. 1 fold seat switch LH OFF
      11 to 14 V
      Back door open
      No. 1 fold seat switch LH folding
      Below 1 V
      RH Side 
      Tester Connection
      Condition
      Specified Condition
      P20-15 (RTRN) - Body ground
      Back door open
      No. 1 fold seat switch RH OFF
      11 to 14 V
      Back door open
      No. 1 fold seat switch RH return
      Below 1 V
      P20-16 (FOLD) - Body ground
      Back door open
      No. 1 fold seat switch RH OFF
      11 to 14 V
      Back door open
      No. 1 fold seat switch RH folding
      Below 1 V



  1. Check No. 2 fold seat switch signal.



      B193667E03
    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      LH Side 
      Tester Connection
      Condition
      Specified Condition
      O34-10 (FLD2) - Body ground
      Rear LH door open
      No. 2 fold seat switch LH OFF
      11 to 14 V
      Rear LH door open
      No. 2 fold seat switch LH folding
      Below 1 V
      O34-14 (RTN2) - Body ground
      Rear LH door open
      No. 2 fold seat switch LH OFF
      11 to 14 V
      Rear LH door open
      No. 2 fold seat switch LH return
      Below 1 V
      RH Side 
      Tester Connection
      Condition
      Specified Condition
      P20-10 (FLD2) - Body ground
      Rear RH door open
      No. 2 fold seat switch RH OFF
      11 to 14 V
      Rear RH door open
      No. 2 fold seat switch RH folding
      Below 1 V
      P20-14 (RTN2) - Body ground
      Rear RH door open
      No. 2 fold seat switch RH OFF
      11 to 14 V
      Rear RH door open
      No. 2 fold seat switch RH return
      Below 1 V

      Result 
      Result
      Proceed to
      OK
      A
      NG (No. 1 fold seat switch signal)
      B
      NG (No. 2 fold seat switch signal)
      C



B
Go to step 2

C
Go to step 5
A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE 

2.READ VALUE USING TECHSTREAM (BACK DOOR COURTESY SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Body Electrical / Back Door P/W / Data List.

  1. According to the display on the Techstream, read the Data List.

    Back Door P/W 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Courtesy Switch
    Back Door Courtesy Switch / ON or OFF
    ON: Back door opened
    OFF: Back door closed
    -

    OK:
    When back door courtesy switch operation is performed, the results are the same as above.



NG
GO TO BACK DOOR COURTESY SWITCH CIRCUIT (Click here)
OK


3.INSPECT NO. 1 FOLD SEAT SWITCH


  1. Remove the No. 1 fold seat switch (Click here).


    B195048E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    LH Side 
    Tester Connection
    Switch Condition
    Specified Condition
    6 (FOLD) - 4 (E)
    No. 1 fold seat switch LH fold
    Below 1 Ω
    No. 1 fold seat switch LH OFF
    10 kΩ or higher
    7 (RTRN) - 4 (E)
    No. 1 fold seat switch LH return
    Below 1 Ω
    No. 1 fold seat switch LH OFF
    10 kΩ or higher
    RH Side 
    Tester Connection
    Switch Condition
    Specified Condition
    3 (FOLD) - 5 (E)
    No. 1 fold seat switch RH fold
    Below 1 Ω
    No. 1 fold seat switch RH OFF
    10 kΩ or higher
    4 (RTRN) - 5 (E)
    No. 1 fold seat switch RH return
    Below 1 Ω
    No. 1 fold seat switch RH OFF
    10 kΩ or higher



NG
REPLACE NO. 1 FOLD SEAT SWITCH (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 1 FOLD SEAT SWITCH)


    B195049E01
  1. Disconnect the O34 or P20 ECU connector.

  1. Disconnect the O27 or O28 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    LH Side 
    Tester Connection
    Condition
    Specified Condition
    O34-15 (RTRN) - O27-7 (RTRN)
    Always
    Below 1 Ω
    O34-15 (RTRN) - Body ground
    Always
    10 kΩ or higher
    O34-16 (FOLD) - O27-6 (FOLD)
    Always
    Below 1 Ω
    O34-16 (FOLD) - Body ground
    Always
    10 kΩ or higher
    RH Side 
    Tester Connection
    Condition
    Specified Condition
    P20-15 (RTRN) - O28-4 (RTRN)
    Always
    Below 1 Ω
    P20-15 (RTRN) - Body ground
    Always
    10 kΩ or higher
    P20-16 (FOLD) - O28-3 (FOLD)
    Always
    Below 1 Ω
    P20-16 (FOLD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BACK DOOR ECU - NO. 1 FOLD SEAT SWITCH) 

5.READ VALUE USING TECHSTREAM (REAR DOOR COURTESY SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RL Door Courtesy SW
    Rear door courtesy light switch LH signal / ON or OFF
    ON: Rear door courtesy light switch LH ON
    OFF: Rear door courtesy light switch LH OFF
    -
    RR Door Courtesy SW
    Rear door courtesy light switch RH signal / ON or OFF
    ON: Rear door courtesy light switch RH ON
    OFF: Rear door courtesy light switch RH OFF
    -

    OK:
    When rear door courtesy light switch operation is performed, the results are the same as above.



NG
GO TO REAR DOOR COURTESY SWITCH CIRCUIT (Click here)
OK


6.INSPECT NO. 2 FOLD SEAT SWITCH


  1. Remove the No. 2 fold seat switch (Click here).


    B195048E02

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    LH Side 
    Tester Connection
    Switch Condition
    Specified Condition
    6 (FOLD) - 4 (E)
    No. 2 fold seat switch LH fold
    Below 1 Ω
    No. 2 fold seat switch LH OFF
    10 kΩ or higher
    7 (RTRN) - 4 (E)
    No. 2 fold seat switch LH return
    Below 1 Ω
    No. 2 fold seat switch LH OFF
    10 kΩ or higher
    RH Side 
    Tester Connection
    Switch Condition
    Specified Condition
    3 (FOLD) - 5 (E)
    No. 2 fold seat switch RH fold
    Below 1 Ω
    No. 2 fold seat switch RH OFF
    10 kΩ or higher
    4 (RTRN) - 5 (E)
    No. 2 fold seat switch RH return
    Below 1 Ω
    No. 2 fold seat switch RH OFF
    10 kΩ or higher



NG
REPLACE NO. 2 FOLD SEAT SWITCH (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 2 FOLD SEAT SWITCH)
  1. Disconnect the O34 or P20 ECU connector.



    B195049E02
  1. Disconnect the O26 or P12 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    LH Side 
    Tester Connection
    Condition
    Specified Condition
    O34-10 (FLD2) - O26-6 (FOLD)
    Always
    Below 1 Ω
    O34-10 (FLD2) - Body ground
    Always
    10 kΩ or higher
    O34-14 (RTN2) - O26-7 (RTRN)
    Always
    Below 1 Ω
    O34-14 (RTN2) - Body ground
    Always
    10 kΩ or higher
    RH Side 
    Tester Connection
    Condition
    Specified Condition
    P20-10 (FLD2) - P12-3 (FOLD)
    Always
    Below 1 Ω
    P20-10 (FLD2) - Body ground
    Always
    10 kΩ or higher
    P20-14 (RTN2) - P12-4 (RTRN)
    Always
    Below 1 Ω
    P20-14 (RTN2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 FOLD SEAT SWITCH - REAR DOOR COURTESY LIGHT SWITCH)