LIGHTING SYSTEM > Door Courtesy Switch Circuit |

| 1.READ VALUE USING TECHSTREAM (DOOR COURTESY LIGHT SWITCH) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Main Body / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| D Door Courtesy SW | Front door courtesy light switch LH signal / ON or OFF | ON: Front door courtesy light switch LH ON OFF: Front door courtesy light switch LH OFF | - |
| P Door Courtesy SW | Front door courtesy light switch RH signal / ON or OFF | ON: Front door courtesy light switch RH ON OFF: Front door courtesy light switch RH OFF | - |
| RL Door Courtesy SW | Rear door courtesy light switch LH signal / ON or OFF | ON: Rear door courtesy light switch LH ON OFF: Rear door courtesy light switch LH OFF | - |
| RR Door Courtesy SW | Rear door courtesy light switch RH signal / ON or OFF | ON: Rear door courtesy light switch RH ON OFF: Rear door courtesy light switch RH OFF | - |
| Result | Proceed to |
| OK | A |
| NG (Front door courtesy light switch LH does not operate) | B |
| NG (Front door courtesy light switch RH does not operate) | C |
| NG (Rear door courtesy light switch LH does not operate) | D |
| NG (Rear door courtesy light switch RH does not operate) | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH LH |
![]() |
Remove the front door courtesy light switch LH (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - Body ground | Not pushed | Below 1 Ω |
| Pushed | 10 kΩ or higher |
Reinstall the front door courtesy light switch LH.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH LH - MAIN BODY ECU) |
![]() |
Disconnect the O8 front door courtesy light switch LH connector.
Disconnect the H4 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O8-1 - H4-24 (DCTY) | Always | Below 1 Ω |
| O8-1 - Body ground | Always | 10 kΩ or higher |
Reconnect the main body ECU connector.
Reconnect the front door courtesy light switch LH connector.
|
| ||||
| OK | ||
| ||
| 4.INSPECT FRONT DOOR COURTESY LIGHT SWITCH RH |
![]() |
Remove the front door courtesy light switch RH (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - Body ground | Not pushed | Below 1 Ω |
| Pushed | 10 kΩ or higher |
Reinstall the front door courtesy light switch RH.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH RH - MAIN BODY ECU) |
![]() |
Disconnect the P6 front door courtesy light switch RH connector.
Disconnect the H3 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P6-1 - H3-21 (PCTY) | Always | Below 1 Ω |
| P6-1 - Body ground | Always | 10 kΩ or higher |
Reconnect the main body ECU connector.
Reconnect the front door courtesy light switch RH connector.
|
| ||||
| OK | ||
| ||
| 6.INSPECT REAR DOOR COURTESY LIGHT SWITCH LH |
![]() |
Remove the rear door courtesy light switch LH (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - Body ground | Not pushed | Below 1 Ω |
| Pushed | 10 kΩ or higher |
Reinstall the rear door courtesy light switch LH.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH LH - MAIN BODY ECU) |
![]() |
Disconnect the O7 rear door courtesy light switch LH connector.
Disconnect the DC main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O7-1 - DC-2 (LCTY) | Always | Below 1 Ω |
| O7-1 - Body ground | Always | 10 kΩ or higher |
Reconnect the main body ECU connector.
Reconnect the rear door courtesy light switch LH connector.
|
| ||||
| OK | ||
| ||
| 8.INSPECT REAR DOOR COURTESY LIGHT SWITCH RH |
![]() |
Remove the rear door courtesy light switch RH (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - Body ground | Not pushed | Below 1 Ω |
| Pushed | 10 kΩ or higher |
Reinstall the rear door courtesy light switch RH.
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH RH - MAIN BODY ECU) |
![]() |
Disconnect the P7 rear door courtesy light switch RH connector.
Disconnect the H3 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P7-1 - H3-25 (RRCY) | Always | Below 1 Ω |
| P7-1 - Body ground | Always | 10 kΩ or higher |
Reconnect the main body ECU connector.
Reconnect the rear door courtesy light switch RH connector.
|
| ||||
| OK | ||
| ||