Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM

DTC    B2342    Switch Failure

for Preparation Click here


DESCRIPTION

This DTC is stored when the sliding roof drive gear (sliding roof ECU) detects that the SLIDE or TILT switch in the roof console box (sliding roof switch) is stuck for 30 seconds or more.

DTC Code
DTC Detection Condition
Trouble Area
B2342
Sliding roof drive gear (sliding roof ECU) detects that SLIDE or TILT switch in roof console box is stuck for 30 seconds or more.
  1. Sliding roof switch
  2. Roof console box
  3. Harness and connector
  4. Sliding roof drive gear (Sliding roof ECU)

WIRING DIAGRAM


B167040E04


INSPECTION PROCEDURE

1.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B2342 is output
    A
    No DTC is output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


2.READ VALUE USING TECHSTREAM (SWITCH STATUS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Body Electrical / Sliding Roof / Data List.

  1. According to the display on the Techstream, read the Data List.

    Sliding Roof 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Open Switch Failure (Past)
    Open switch failure signal (Past)/Fail or Not Fail
    Fail: Sliding roof tilt open signal failure (Past)
    Not Fail: Sliding roof tilt open signal not fail (Past)
    -
    Close Switch Failure (Past)
    Close switch failure signal (Past)/Fail or Not Fail
    Fail: Sliding roof tilt close signal failure (Past)
    Not Fail: Sliding roof tilt close signal not fail (Past)
    -
    Up Switch Failure (Past)
    Up switch failure signal (Past)/Fail or Not Fail
    Fail: Sliding roof tilt up signal failure (Past)
    Not Fail: Sliding roof tilt up signal not fail (Past)
    -
    Down Switch Failure (Past)
    Down switch failure signal (Past)/Fail or Not Fail
    Fail: Sliding roof tilt down signal failure (Past)
    Not Fail: Sliding roof tilt down signal not fail (Past)
    -
    Open Switch Failure (Current)
    Open switch failure signal (Current)/Fail or Not Fail
    Fail: Sliding roof tilt open signal failure (Current)
    Not Fail: Sliding roof tilt open signal not fail (Current)
    -
    Close Switch Failure (Current)
    Close switch failure signal (Current)/Fail or Not Fail
    Fail: Sliding roof tilt close signal failure (Current)
    Not Fail: Sliding roof tilt close signal not fail (Current)
    -
    Up Switch Failure (Current)
    Up switch failure signal (Current)/Fail or Not Fail
    Fail: Sliding roof tilt up signal failure (Current)
    Not Fail: Sliding roof tilt up signal not fail (Current)
    -
    Down Switch Failure (Current)
    Down switch failure signal (Current)/Fail or Not Fail
    Fail: Sliding roof tilt down signal failure (Current)
    Not Fail: Sliding roof tilt down signal not fail (Current)
    -

    OK:
    The Techstream displays as shown in the table according to the operation of each switch.



NG
Go to step 3
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (Click here)  

3.INSPECT SLIDING ROOF SWITCH


    B167041E05
  1. Remove the sliding roof switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (UP) - 5 (E)
    TILT switch is pressed to up
    Below 1 Ω
    TILT switch is not pressed to up
    10 kΩ or higher
    2 (DOWN) - 5 (E)
    TILT switch is pressed to down
    Below 1 Ω
    TILT switch is not pressed to down
    10 kΩ or higher
    3 (CLS) - 5 (E)
    SLIDE switch is pressed to close
    Below 1 Ω
    SLIDE switch is not pressed to close
    10 kΩ or higher
    4 (OPN) - 5 (E)
    SLIDE switch is pressed to open
    Below 1 Ω
    SLIDE switch is not pressed to open
    10 kΩ or higher



NG
REPLACE SLIDING ROOF SWITCH (Click here)
OK


4.INSPECT ROOF CONSOLE BOX ASSEMBLY
E146741E03
  1. Remove the roof console box with sliding roof switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (CLS) - 7 (E)
    SLIDE switch is pressed to close
    Below 1 Ω
    SLIDE switch is not pressed to close
    10 kΩ or higher
    4 (OPN) - 7 (E)
    SLIDE switch is pressed to open
    Below 1 Ω
    SLIDE switch is not pressed to open
    10 kΩ or higher
    5 (DOWN) - 7 (E)
    TILT switch is pressed to down
    Below 1 Ω
    TILT switch is not pressed to down
    10 kΩ or higher
    6 (UP) - 7 (E)
    TILT switch is pressed to up
    Below 1 Ω
    TILT switch is not pressed to up
    10 kΩ or higher



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (ROOF CONSOLE BOX - SLIDING ROOF ECU AND BODY GROUND)
B171201E02
  1. Disconnect the U3 ECU connector.

  1. Disconnect the U7 roof console box connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U7-3 (CLS) - U3-7 (CLS)
    Always
    Below 1 Ω
    U7-3 (CLS) - Body ground
    Always
    10 kΩ or higher
    U7-4 (OPN) - U3-6 (OPN)
    Always
    Below 1 Ω
    U7-4 (OPN) - Body ground
    Always
    10 kΩ or higher
    U7-5 (DOWN) - U3-2 (DWN)
    Always
    Below 1 Ω
    U7-5 (DOWN) - Body ground
    Always
    10 kΩ or higher
    U7-6 (UP) - U3-1 (UP)
    Always
    Below 1 Ω
    U7-6 (UP) - Body ground
    Always
    10 kΩ or higher
    U7-7 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (Click here)