Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM

DTC    B2343    Position Initialization Incomplete

for Preparation Click here


DESCRIPTION

This DTC is stored when the sliding roof drive gear (sliding roof ECU) has not been initialized.

DTC Code
DTC Detection Condition
Trouble Area
B2343
Sliding roof drive gear (sliding roof ECU) has not been initialized
Sliding roof drive gear (Sliding roof ECU)

WIRING DIAGRAM


B167040E04


INSPECTION PROCEDURE

1.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
  1. Check that the sliding roof drive gear can be initialized (Click here).

    OK:
    Sliding roof drive gear can be initialized.



NG
Go to step 3
OK


2.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTC B2343 is output
    B



B
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (Click here)
A

END 

3.CHECK HARNESS AND CONNECTOR (ROOF CONSOLE BOX - SLIDING ROOF ECU AND BODY GROUND)


    B171201E02
  1. Disconnect the U3 ECU connector.

  1. Disconnect the U7 roof console box connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U7-3 (CLS) - U3-7 (CLS)
    Always
    Below 1 Ω
    U7-3 (CLS) - Body ground
    Always
    10 kΩ or higher
    U7-4 (OPN) - U3-6 (OPN)
    Always
    Below 1 Ω
    U7-4 (OPN) - Body ground
    Always
    10 kΩ or higher
    U7-5 (DOWN) - U3-2 (DWN)
    Always
    Below 1 Ω
    U7-5 (DOWN) - Body ground
    Always
    10 kΩ or higher
    U7-6 (UP) - U3-1 (UP)
    Always
    Below 1 Ω
    U7-6 (UP) - Body ground
    Always
    10 kΩ or higher
    U7-7 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT SLIDING ROOF SWITCH


    B167041E05
  1. Remove the sliding roof switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (UP) - 5 (E)
    TILT switch is pressed to up
    Below 1 Ω
    TILT switch is not pressed to up
    10 kΩ or higher
    2 (DOWN) - 5 (E)
    TILT switch is pressed to down
    Below 1 Ω
    TILT switch is not pressed to down
    10 kΩ or higher
    3 (CLS) - 5 (E)
    SLIDE switch is pressed to close
    Below 1 Ω
    SLIDE switch is not pressed to close
    10 kΩ or higher
    4 (OPN) - 5 (E)
    SLIDE switch is pressed to open
    Below 1 Ω
    SLIDE switch is not pressed to open
    10 kΩ or higher



NG
REPLACE SLIDING ROOF SWITCH (Click here)
OK


5.INSPECT ROOF CONSOLE BOX ASSEMBLY


    E146741E03
  1. Remove the roof console box with sliding roof switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (CLS) - 7 (E)
    SLIDE switch is pressed to close
    Below 1 Ω
    SLIDE switch is not pressed to close
    10 kΩ or higher
    4 (OPN) - 7 (E)
    SLIDE switch is pressed to open
    Below 1 Ω
    SLIDE switch is not pressed to open
    10 kΩ or higher
    5 (DOWN) - 7 (E)
    TILT switch is pressed to down
    Below 1 Ω
    TILT switch is not pressed to down
    10 kΩ or higher
    6 (UP) - 7 (E)
    TILT switch is pressed to up
    Below 1 Ω
    TILT switch is not pressed to up
    10 kΩ or higher



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (Click here)
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (Click here)