Home › Engine / Hybrid System ยท 2UZ-FE › COOLING › RADIATOR

RADIATOR > REMOVAL

for Preparation Click here



1. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



2. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs.

  1. Remove the radiator cap. Then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 10 ft.*lbf }



    A156211E01

  1. Tighten the radiator drain cock plug by hand.



3. REMOVE FRONT BUMPER COVER
  1. Remove the front bumper cover (Click here).



4. REMOVE RADIATOR SIDE DEFLECTOR LH


A185304
  1. Remove the 6 clips and side deflector.

  1. Disconnect the wire harness clamp.



5. REMOVE RADIATOR SIDE DEFLECTOR RH (w/o Trailer Towing System)


A185305
  1. Remove the 6 clips and side deflector.



6. REMOVE THROTTLE BODY COVER SUB-ASSEMBLY


    A153486
  1. Remove the 2 nuts and throttle body cover sub-assembly.



7. REMOVE AIR CLEANER HOSE ASSEMBLY


    A153487
  1. Disconnect the vacuum hose and No. 2 ventilation hose.

  1. Loosen the 2 hose clamps and remove the air cleaner hose assembly.



8. REMOVE INLET RADIATOR HOSE


A185306
  1. Remove the inlet radiator hose.



9. REMOVE FAN SHROUD (w/ Trailer Towing System)


A162053
  1. Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the fan and generator V-belt .



    A161784
  1. Detach the claw to open the No. 1 flexible hose clamp.



    A185308
  1. Disconnect the reservoir hose.



    A156168
  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the fan shroud together with the fluid coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump.



10. REMOVE FAN SHROUD (w/o Trailer Towing System)


A162053
  1. Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the fan and generator V belt .



    A185308
  1. Disconnect the reservoir hose.



    A156168
  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the fan shroud together with the fluid coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump.



11. REMOVE OIL COOLER ASSEMBLY (w/ Trailer Towing System)


    C179235
  1. Remove the 3 bolts and air cooled oil cooler assembly.



    C179236
  1. Remove the 2 bolts and oil cooler support bracket.



12. DISCONNECT OUTLET RADIATOR HOSE


A185307
  1. Disconnect the outlet radiator hose.



13. REMOVE NO. 1 RADIATOR TO SUPPORT SEAL


A185302E01
  1. Remove the 3 clips and No. 1 radiator to support seal.



14. REMOVE RADIATOR ASSEMBLY


    A185309
  1. Remove the 4 bolts and radiator assembly.



15. REMOVE OUTLET RADIATOR HOSE
  1. Remove the outlet radiator hose from the radiator assembly.



16. REMOVE RADIATOR DRAIN COCK PLUG
  1. Remove the radiator drain cock plug from the radiator assembly.