Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1690/15    Driver Side Door Side Airbag Sensor Malfunction

DTC    B1695/16    Passenger Side Door Side Airbag Sensor Malfunction

for Preparation Click here


DESCRIPTION

The side airbag sensor LH or RH consists of the safing sensor, the diagnostic circuit, the lateral deceleration sensor, etc.
If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
DTC B1690/15 or B1695/16 is stored when a malfunction is detected in the side airbag sensor LH or RH circuit.

DTC Code
Detection Condition
Trouble Area
B1690/15
When both conditions below are met:
  1. Side airbag sensor LH malfunction
  2. Center airbag sensor malfunction
  1. Side airbag sensor LH
  2. Rear airbag sensor LH
  3. Center airbag sensor assembly
  4. Floor wire
  5. Front door wire LH
B1695/16
When both conditions below are met:
  1. Side airbag sensor RH malfunction
  2. Center airbag sensor malfunction
  1. Side airbag sensor RH
  2. Rear airbag sensor RH
  3. Center airbag sensor assembly
  4. No. 2 floor wire
  5. Front door wire RH

WIRING DIAGRAM


C179187E01


C179187E02


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1695/16 is output
    A
    DTC B1690/15 is output
    B
    DTC B1690/15 and B1695/16 are not output
    C

    HINT:
    Codes other than past DTC B1690/15 and B1695/16 may be output at this time, but they are not related to this check.



B
Go to step 12

C
USE SIMULATION METHOD TO CHECK (Click here)
A


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the side airbag sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and side airbag sensor RH.

  1. Check that the connectors (on the center airbag sensor side and the side airbag sensor RH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


4.CHECK SIDE AIRBAG SENSOR RH CIRCUIT

C179618E01

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L9-4 (BBR+) - Body ground
    Ignition switch ON
    Below 1 V
    L9-3 (BBR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the center airbag sensor and side airbag sensor RH.

  1. Using a service wire, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L9-4 (BBR+) - L9-3 (BBR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from the connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L9-4 (BBR+) - L9-3 (BBR-)
    Always
    1 MΩ or higher
    L9-4 (BBR+) - Body ground
    Always
    1 MΩ or higher
    L9-3 (BBR-) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 10
OK


5.CHECK SIDE AIRBAG SENSOR RH


    C171827E12
  1. Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 90 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1695/16 is output
    A
    DTC B1690/15 is output
    B
    DTC B1690/15 and B1695/16 are not output
    C

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



B
REPLACE SIDE AIRBAG SENSOR RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


6.CHECK CONNECTION OF CONNECTORS
  1. Check that the connector are properly connected to the rear airbag sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


7.CHECK CONNECTORS
  1. Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.

  1. Check that the connectors (on the rear airbag sensor RH side) is not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


8.CHECK REAR AIRBAG SENSOR RH CIRCUIT

C179619E01

  1. Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L9-1 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    L9-2 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.

  1. Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector E.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L9-1 (BCR+) - L9-2 (BCR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from the connector E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L9-1 (BCR+) - L9-2 (BCR-)
    Always
    1 MΩ or higher
    L9-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    L9-2 (BCR-) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 11
OK


9.CHECK REAR AIRBAG SENSOR RH
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the rear airbag sensor RH connector.

  1. Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

OK:
DTC B1695/16 is output.



NG
REPLACE REAR AIRBAG SENSOR RH (Click here)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

10.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT DOOR WIRE RH)

C180139E01

  1. Disconnect the No. 2 floor wire connector from the door wire RH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    LP1-4 (BBR+) - Body ground
    Ignition switch ON
    Below 1 V
    LP1-3 (BBR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    LP1-4 (BBR+) - LP1-3 (BBR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    LP1-4 (BBR+) - LP1-3 (BBR-)
    Always
    1 MΩ or higher
    LP1-4 (BBR+) - Body ground
    Always
    1 MΩ or higher
    LP1-3 (BBR-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT DOOR WIRE RH 

11.CHECK FRONT DOOR WIRE RH (SIDE AIRBAG SENSOR RH - NO. 2 FLOOR WIRE)

C172034E09

  1. Disconnect the No. 2 floor wire connector from the door wire RH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L9-1 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    L9-2 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L9-1 (BCR+) - L9-2 (BCR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L9-1 (BCR+) - L9-2 (BCR-)
    Always
    1 MΩ or higher
    L9-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    L9-2 (BCR-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FRONT DOOR WIRE RH
OK

REPLACE NO. 2 FLOOR WIRE 

12.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the side airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


13.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and side airbag sensor LH.

  1. Check that the connectors (on the center airbag sensor side and the side airbag sensor LH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


14.CHECK SIDE AIRBAG SENSOR LH CIRCUIT

C180140E01

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M11-4 (BBL+) - Body ground
    Ignition switch ON
    Below 1 V
    M11-3 (BBL-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the side airbag sensor LH and door side airbag sensor LH.

  1. Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M11-4 (BBL+) - M11-3 (BBL-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from the connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M11-4 (BBL+) - M11-3 (BBL-)
    Always
    1 MΩ or higher
    M11-4 (BBL+) - Body ground
    Always
    1 MΩ or higher
    M11-3 (BBL-) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 20
OK


15.CHECK SIDE AIRBAG SENSOR LH


    C180158E01
  1. Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1690/15 is output
    A
    DTC B1695/16 is output
    B
    DTC B1690/15 and B1695/16 are not output
    C

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



B
REPLACE SIDE AIRBAG SENSOR LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


16.CHECK CONNECTION OF CONNECTORS
  1. Check that the connector are properly connected to the rear airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


17.CHECK CONNECTORS
  1. Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.

  1. Check that the connectors (on the rear airbag sensor LH side) is not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


18.CHECK REAR AIRBAG SENSOR LH CIRCUIT

C179619E02

  1. Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M11-1 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    M11-2 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.

  1. Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector E.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M11-1 (BCL+) - M11-2 (BCL-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from the connector E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M11-1 (BCL+) - M11-2 (BCL-)
    Always
    1 MΩ or higher
    M11-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    M11-2 (BCL-) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 21
OK


19.CHECK REAR AIRBAG SENSOR LH
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the rear airbag sensor LH connector.

  1. Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

OK:
DTC B1690/15 is output.



NG
REPLACE REAR AIRBAG SENSOR LH (Click here)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

20.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT DOOR WIRE LH)

C180159E01

  1. Disconnect the floor wire connector from the door wire LH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    MO1-4 (BBL+) - Body ground
    Ignition switch ON
    Below 1 V
    MO1-3 (BBL-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    MO1-4 (BBL+) - MO1-3 (BBL-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    MO1-4 (BBL+) - MO1-3 (BBL-)
    Always
    1 MΩ or higher
    MO1-4 (BBL+) - Body ground
    Always
    1 MΩ or higher
    MO1-3 (BBL-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK

REPLACE FRONT DOOR WIRE LH 

21.CHECK FRONT DOOR WIRE LH (SIDE AIRBAG SENSOR LH - FLOOR WIRE)

C172034E10

  1. Disconnect the floor wire connector from the door wire LH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M11-1 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    M11-2 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M11-1 (BCL+) - M11-2 (BCL-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M11-1 (BCL+) - M11-2 (BCL-)
    Always
    1 MΩ or higher
    M11-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    M11-2 (BCL-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FRONT DOOR WIRE LH
OK

REPLACE FLOOR WIRE