DTC P050A Cold Start Idle Air Control System Performance |
| DTC No. | DTC Detection Condition | Trouble Area |
| P050A | Insufficient mass air flow at cold start (2 trip detection logic) |
|

| Related DTCs | P050A: Cold start idle air speed control system |
| Required sensors/Components (Main) | Throttle body |
| Required sensors/Components (Related) | Mass air flow meter Engine coolant temperature sensor |
| Frequency of operation | Once per driving cycle |
| Duration | 10 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| Monitor will run whenever these DTCs are not present | P0010, P0020 (VVT Oil Control Valve) P0011, P0021 (VVT System - Advance) P0012, P0022 (VVT System - Retard) P0016, P0018 (VVT System - Misalignment) P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256, P2A00, P2A03 (Air Fuel Ratio Sensor) P0102, P0103 (Mass Air Flow Sensor) P0115, P0117, P0118 (Engine Coolant Temperature Sensor) P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor) P0171, P0172, P0174, P0175 (Fuel System) P0300 - P0308 (Misfire) P0335 (Crankshaft Position Sensor) P1340 (Camshaft Position Sensor) P0340, P0345 (VVT Sensor) P0351 - P0358 (Igniter) P0500 (Vehicle Speed Sensor) P0705 (Shift Lever Position Switch) |
| Battery voltage | 8 V or more |
| Time after engine start | 3 seconds or more |
| Starter | OFF |
| ECT at engine start | -10°C (14°F) or more |
| ECT | -10 to 50°C (14 to 122°F) |
| Engine idling | 3 seconds or more |
| Fuel-cut | OFF |
| Vehicle speed | Less than 1.875 mph (3 km/h) |
| Atmospheric pressure | 76 kPa (570 mmHg) or more |
| Accumulated mass air flow | Less than 52.4 g (varies with ECT) |
| 1.CHECK DTCS |
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (FUEL TRIM) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Powertrain / Engine / Data List / A/F Control System / Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2.
Read the values displayed on the Techstream.
Add together the Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values to obtain the total Fuel Trim.
|
| ||||
| OK | |
| 3.INSPECT THROTTLE BODY |
Check for deposits around the throttle valve and throttle valve condition.
|
| ||||
|
| ||||
| 4.CHECK VVT SYSTEM |
Allow the engine to idle with the engine warmed up.
Enter the following menus using the Techstream: Powertrain / Engine / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).
Turn on Control the VVT System (Bank 1) or Control the VVT System (Bank 2) to advance the valve timing.
Check the engine condition.
|
| ||||
| OK | |
| 5.CHECK PCV SYSTEM |
Allow the engine to idle.
Pinch the positive crankcase ventilation (PCV) hose.
Check the engine rpm.
|
| ||||
| OK | |
| 6.INSPECT AIR CLEANER FILTER |
Visually check that the air cleaner filter is not excessively contaminated with dirt or oil.
|
| ||||
| OK | |
| 7.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leak .
|
| ||||
|
| ||||
| 8.REPAIR OR REPLACE THROTTLE BODY |
Repair or replace the throttle body (Click here).
|
| ||||
| 9.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 10.CHECK AND REPAIR VVT SYSTEM |
|
| ||||
| 11.REPAIR OR REPLACE PCV HOSE |
|
| ||||
| 12.REPLACE AIR CLEANER FILTER |
|
| ||||
| 13.REPAIR OR REPLACE AIR INDUCTION SYSTEM |
|
| ||||
| 14.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
| NEXT | |
| 15.CHECK DTCS |
Check that the engine coolant temperature is -10 to 50°C (14 to 122°F).
Clear the DTC (Click here).
Enter the check mode using the Techstream (Click here).
Allow the engine to idle for 1 minute.
Check that no DTC is present.
| NEXT | ||
| ||