Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1421/21    Solar Sensor Circuit (Passenger Side)

for Preparation Click here


DESCRIPTION

The Automatic light control sensor (solar sensor), which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning in AUTO mode. The output current from the solar sensor varies according to the amount of sunlight. When the sunlight increases, the output current increases. As the sunlight decreases, the output current decreases. The air conditioning amplifier detects output current from the automatic light control sensor (solar sensor).
E132508E01

DTC Code
DTC Detection Condition
Trouble Area
B1421/21
Open or short in passenger side solar sensor circuit
  1. Automatic light control sensor (solar sensor)
  2. Harness or connector between automatic light control sensor (solar sensor) and air conditioning amplifier
  3. Harness or connector between automatic light control sensor (solar sensor) and main body ECU
  4. Main body ECU
  5. Air conditioning amplifier

WIRING DIAGRAM


E147579E03


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (SOLAR SENSOR (P SIDE))
  1. Connect the Techstream to DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Air Conditioner / Data List / Solar Sensor (P Side).

  1. According to the display on the Techstream, read the Data List.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Solar Sensor (P Side)
    Passenger side solar sensor /
    Min.: 0
    Max.: 255
    Passenger side solar sensor voltage increases as brightness increases
    Open in circuit: 0
    Short in circuit: 255

    OK:
    The display is as specified in the normal condition.


    Result 
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC output)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
A


2.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR SYSTEM VOLTAGE)


    E107010E13
  1. Disconnect the I21 Automatic light control sensor (solar sensor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I21-3 (CLTE) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I21-6 (CLTB) - I21-3 (CLTE)
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

  1. Reconnect the automatic light control sensor (solar sensor) connector.



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - AUTOMATIC LIGHT CONTROL SENSOR)


    E127612E03
  1. Disconnect the H24 air conditioning amplifier connector.

  1. Disconnect the I21 automatic light control sensor (solar sensor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H24-32 (TSP) - I21-2 (TSR)
    Always
    Below 1 Ω
    H24-32 (TSP) or I21-2 (TSR) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the solar sensor connector.

  1. Reconnect the air conditioning amplifier connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK AUTOMATIC LIGHT CONTROL SENSOR (SOLAR SENSOR (TSR - CLTE VOLTAGE))


    E108193E25
  1. Remove the automatic light control sensor (solar sensor) with its connector still connected (Click here).

  1. Apply battery voltage between terminals 6 (CLTB) and 3 (CLTE) of the solar sensor.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    2 (TSR) - 3 (CLTE)
    Sensor is subjected to electric light
    0.8 to 4.3 V
    Sensor is covered with a cloth
    Below 0.8 V

    HINT:
    1. As the inspection light is moved away from the sensor, the voltage decreases.
    2. Use an incandescent light for inspection. Bring it about 30 cm (11.8 in.) from the solar sensor.

  1. Reinstall the Automatic light control sensor (solar sensor) sensor.



NG
REPLACE AUTOMATIC LIGHT CONTROL SENSOR (SOLAR SENSOR) (Click here)
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)  

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR, BODY GROUND)


    E146407E03
  1. Disconnect the H3 main body ECU connector.

  1. Disconnect the I21 automatic light control sensor (solar sensor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H3-18 (CLTE) - I21-3 (CLTE)
    Always
    Below 1 Ω
    H3-20 (CLTB) - I21-6 (CLTB)
    Always
    Below 1 Ω
    H3-18 (CLTE) or I21-3 (CLTE) - Body ground
    Always
    10 kΩ or higher
    H3-20 (CLTB) or I21-6 (CLTB) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the automatic light control sensor (solar sensor) connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU