Home › Engine / Hybrid System ยท 2UZ-FE › ENGINE MECHANICAL › CYLINDER HEAD GASKET

CYLINDER HEAD GASKET > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E161312
  1. Remove the nut and remove the wiper arm and blade assembly.



3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

HINT:
Use the same procedure for both sides.



4. REMOVE FRONT FENDER TO COWL SIDE SEAL RH


    E161313
  1. Disengage the claw and remove the front fender to cowl side seal.



5. REMOVE FRONT FENDER TO COWL SIDE SEAL LH

HINT:
Use the same procedure for both sides.



6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E161315
  1. Remove the 2 clips.

  1. Remove the 6 claws and 8 guides and remove the cowl top ventilator louver sub-assembly.



7. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY


    E161316
  1. Disconnect the connector.

  1. Remove the nut.

  1. Remove the 4 bolts and wiper motor and link assembly.



8. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY
  1. Disconnect the washer hose.

  1. Separate the washer hose grommet from the front cowl top outer panel sub-assembly.

  1. Separate the wire harness clamp from the front cowl top outer panel sub-assembly.



  1. Remove the 7 bolts and front cowl top outer panel sub-assembly.


    A151796



9. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



10. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs.

  1. Remove the radiator cap. Then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 10 ft.*lbf }



    A156211E01

  1. Tighten the radiator drain cock plug by hand.



11. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    A185633
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector and 2 clamps.

  1. Remove the 2 bolts from the center exhaust pipe assembly.

  1. Remove the 3 nuts and front exhaust pipe assembly pipe.



12. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY


    A185632
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector.

  1. Remove the 2 bolts and 2 nuts from the front No. 3 exhaust pipe sub-assembly.

  1. Remove the 3 nuts and front No. 2 exhaust pipe assembly pipe.



13. REMOVE CAMSHAFT
  1. Remove the camshaft (Click here).



14. DISCONNECT VACUUM HOSE ASSEMBLY


    A156175
  1. Remove the bolt and disconnect the vacuum hose assembly.



15. REMOVE NO. 3 WATER BY-PASS PIPE


    A156176
  1. Disconnect the 2 water hoses from the No. 2 water by-pass pipe.



    A156177
  1. Remove the 2 bolts.

  1. Disconnect the 2 water hoses and remove the No. 2 water by-pass pipe.



16. REMOVE EFI FUEL PIPE CLAMP


A185283
  1. Remove the fuel pipe clamp.



17. DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY


A160926
  1. Disconnect the No. 2 fuel pipe sub-assembly (Click here).

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



18. DISCONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY


A185285E01
  1. Disconnect the No. 1 fuel pipe sub-assembly (Click here).

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



19. REMOVE INTAKE MANIFOLD


    A156170
  1. Disconnect the throttle body connector.

  1. Disconnect the 2 water by-pass hoses from the throttle body assembly.



    A166383
  1. Loose the 2 clamps and remove the No. 1 ventilation hose.



    A156171
  1. Disconnect the purge VSV connector.

  1. Disconnect the purge line hose from the purge VSV.



    A166384
  1. Disconnect the vacuum switching valve assembly (for ACIS) connector.



    A166385
  1. Disconnect the wire harness clamp from the engine hanger.

  1. Remove the bolt and wire harness bracket from the intake manifold assembly.



    A163553
  1. Disconnect the 2 wire clamps.

  1. Disconnect the 8 injector connectors.



    A156173
  1. Remove the 2 bolts and separate the engine wire protector.



    A156172
  1. Remove the 6 bolts, 4 nuts, intake manifold assembly and 2 gaskets.



20. REMOVE INLET WATER HOUSING


    A122973
  1. Disconnect the water by-pass hose from the inlet water housing.

  1. Remove the 2 bolts and inlet water housing with water inlet.

  1. Remove the O-ring from the inlet water housing.



21. REMOVE FRONT WATER BY-PASS JOINT


A115096
  1. Remove the 4 nuts, water by-pass joint and 2 gaskets.



22. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY


A160760E03
  1. Remove the bolt and pull out the water by-pass pipe sub-assembly.

  1. Remove the O-ring from the water by-pass pipe sub-assembly.



23. REMOVE REAR WATER BY-PASS JOINT


A160761
  1. Disconnect the air hose and remove the 4 nuts, water by-pass joint and 2 gaskets.



24. REMOVE VALVE LIFTER
  1. Remove the valve lifters and shims from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



25. REMOVE CYLINDER HEAD LH (for Bank 1)


    A115101E03
  1. Uniformly loosen the 10 cylinder head bolts on the cylinder head in several passes, in the sequence shown in the illustration.

  1. Remove the bolts and plate washers.

    NOTICE:
    1. Cylinder head warpage or cracking could result from removing bolts in the incorrect order.
    2. Do not drop the plate washer for the cylinder head bolt into portion A of the cylinder head. If dropped into portion A, the plate washer will pass through the cylinder head and cylinder block into the oil pan.



    A134397
  1. Remove the cylinder head by prying between the cylinder block and cylinder head with a screwdriver.

    NOTICE:
    1. Be careful not to damage the contact surfaces of the cylinder head and cylinder block.
    2. The cylinder head should not be tilted so as to secure the valve lifter. If the cylinder head is tilted, remove the valve lifter and check that the adjusting shim is set correctly.



26. REMOVE NO. 2 CYLINDER HEAD GASKET


27. REMOVE CYLINDER HEAD SUB-ASSEMBLY (for Bank 2)


    A115100E03
  1. Uniformly loosen the 10 cylinder head bolts on the cylinder head in several passes, in the sequence shown in the illustration.

  1. Remove the bolts and plate washers.

    NOTICE:
    1. Cylinder head warpage or cracking could result from removing bolts in the incorrect order.
    2. Do not drop the plate washer for the cylinder head bolt into portion A of the cylinder head. If dropped into portion A, the plate washer will pass through the cylinder head and cylinder block into the oil pan.



    A185320
  1. Remove the cylinder head by prying between the cylinder block and cylinder head with a screwdriver.

    NOTICE:
    1. Be careful not to damage the contact surfaces of the cylinder head and cylinder block.
    2. The cylinder head should not be tilted so as to secure the valve lifter. If the cylinder head is tilted, remove the valve lifter and check that the adjusting shim is set correctly.



28. REMOVE CYLINDER HEAD GASKET