Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > OPERATION CHECK

for Preparation Click here



INSPECT INDICATOR/WARNING LIGHT

HINT:
In this inspection, an indicator or warning light might come on differently than is specified, under some normal conditions.

  1. Check the following indicators and warning lights.
    Warning/Indicator Light
    Switch Condition
    Specified Condition
    Height control HI indicator light*1
    Ignition switch off → ON
    Comes on for 2 seconds
    Height control N indicator light*1
    Ignition switch off → ON
    Comes on for 2 seconds
    Height control LO indicator light*1
    Ignition switch off → ON
    Comes on for 2 seconds
    Height control MAN. indicator light*1
    Ignition switch off → ON
    Comes on for 2 seconds
    Brake warning light
    Ignition switch off → ON
    Comes on for 3 seconds
    ABS warning light
    Ignition switch off → ON
    Comes on for 3 seconds
    SLIP indicator light
    Ignition switch off → ON
    Comes on for 3 seconds
    AUTO LSD indicator light
    Ignition switch off → ON
    Comes on for 3 seconds
    VSC OFF indicator light
    Ignition switch off → ON
    Comes on for 3 seconds
    RSCA OFF indicator light
    Ignition switch off → ON
    Comes on for 3 seconds
    TOW HAUL indicator light*2
    Ignition switch off → ON
    Comes on for 3 seconds
    EPS warning light
    Ignition switch off → ON
    Comes on for 3 seconds
    Tire pressure warning light
    Ignition switch off → ON
    Comes on for 3 seconds
    MAIN REQD indicator light*3
    Ignition switch off → ON
    Comes on for 3 seconds
    SRS warning light
    Ignition switch off → ON
    Comes on for 6 seconds
    A/T OIL TEMP warning light
    Ignition switch off → ON
    Illuminates when ignition switch is turned to ON.
    Turns off when engine is started.
    CHARGE warning light
    Ignition switch off → ON
    Illuminates when ignition switch is turned to ON.
    Turns off when engine is started.
    MIL
    Ignition switch off → ON
    Illuminates when ignition switch is turned to ON.
    Turns off when engine is started.

    HINT:
    *1: w/ Air Suspension
    *2: for 3UR-FE, 3UR-FBE with Towing Package
    *3: for U.S.A. without Multi-information Display


INSPECT SPEEDOMETER
  1. Using a speedometer tester, check that the speedometer reading is within the allowable range shown in the table below. Also, check for proper operation of the odometer.

    Reference:
    for mph 
    Standard Indication
    Acceptable Range
    20 mph
    19 to 22 mph
    40 mph
    39 to 42.5 mph
    60 mph
    59.5 to 63.5 mph
    80 mph
    79.5 to 84 mph
    100 mph
    100 to 105 mph
    for km/h 
    Standard Indication
    Acceptable Range
    Data in ( ) is for reference
    20 km/h
    (17.5 to 21.5 km/h)
    40 km/h
    38 to 42 km/h
    60 km/h
    58 to 63 km/h
    80 km/h
    78 to 84 km/h
    100 km/h
    98.5 to 104.5 km/h
    120 km/h
    119 to 125 km/h
    140 km/h
    139 to 146 km/h
    160 km/h
    159 to 167 km/h
    180 km/h
    179 to 188 km/h

    NOTICE:
    Do not use worn, underinflated or overinflated tires, as the speedometer reading will be inaccurate.

  2. Check the deflection width of the speedometer indicator.

    Reference:
    0.5 km/h (0.3 mph)


INSPECT TACHOMETER
  1. Connect a tune-up tachometer, and start the engine.

  2. Compare the test results with the tachometer indicator.

    DC 13.5 V, at 25°C (77°F):
    Standard indication (rpm)
    Acceptable range
    Data in ( ) is for reference
    700
    630 to 770
    1000
    (900 to 1100)
    2000
    (1850 to 2150)
    3000
    2800 to 3200
    4000
    (3800 to 4200)
    5000
    4800 to 5200
    6000
    (5750 to 6250)

    If the result is not as specified, the speedometer may have a malfunction.


INSPECT METER/GAUGE
  1. Connect the Techstream to the DLC3.

  2. Perform Active Test (Click here).

    OK:
    All meter/gauge needle indicators are normal.


INSPECT WARNING/INDICATOR LIGHT
  1. Connect the Techstream to the DLC3.

  2. Perform Active Test (Click here).

    OK:
    Each warning/indicator light turns ON and OFF using tester.


INSPECT MULTI-INFORMATION DISPLAY (w/ Multi-information display)
  1. Connect the Techstream to the DLC3.

  2. Perform Active Test (Click here).

    HINT:
    If this Active Test is being performed and the ignition switch is turned off and then ON, the A/T and ODO/TRIP display background may turn white. If this occurs, end this Active Test and turn the ignition switch off.

    OK:
    All dots in the multi-information display turn ON and OFF using Techstream.