Home › Drivetrain · JF3A TRANSFER / 4WD / AWD › 4WD CONTROL SWITCH

4WD CONTROL SWITCH > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT 4WD CONTROL SWITCH


  1. Check the harness and connector (ECU - battery and body ground).



      C160037E14
    1. Measure the voltage and resistance according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      A26-3 (IG) - Body ground
      Ignition switch ON
      11 to 14 V

      If there is a malfunction, inspect the harness or connector. If the harness is malfunctioning, repair or replace harness or connector. If the harness or connector is normal, replace the 4WD control ECU (Click here).

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A26-4 (GND) - Body ground
      Always
      Below 1 Ω

      If there is a malfunction, repair or replace the harness or connector.



  1. Check the harness and connector (switch - ECU).

    1. Disconnect the A25 ECU connector.

    2. Disconnect the L1 switch connector.



    3. Measure the resistance according to the value(s) in the table below.


      C160385E01

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L1-2 (LO) - A25-13 (LO)
      Always
      Below 1 Ω
      L1-2 (LO) - Body ground
      Always
      10 kΩ or higher
      L1-4 (GND) - Body ground
      Always
      Below 1 Ω
      L1-5 (2-4) - A25-11 (2-4)
      Always
      Below 1 Ω
      L1-5 (2-4) - Body ground
      Always
      10 kΩ or higher

      If the resistance is not as specified, repair or replace the harness or connector.



  1. Check the 4WD control switch.

    1. Turn the ignition switch off.

    2. Connect the L1 switch connector.

    3. Connect the A25 and A26 ECU connectors.



    4. C160037E03
    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A25-11 (2-4) - Body ground
      Ignition switch ON
      4WD control switch 2WD position
      Below 1.5 V
      Ignition switch ON
      4WD control switch 4H position
      Below 1.5 V
      Ignition switch ON
      4WD control switch 4L position
      10.5 to 14 V
      A25-13 (LO) - Body ground
      Ignition switch ON
      4WD control switch 2WD position
      10.5 to 14 V
      Ignition switch ON
      4WD control switch 4H position
      Below 1.5 V
      Ignition switch ON
      4WD control switch 4L position
      Below 1.5 V

      If the voltage is not as specified, check the 4WD control ECU.



  1. Check the 4WD control ECU.

    1. Disconnect the L1 switch connector.



    2. C160390E01
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      L1-2 (LO) - Body ground
      Ignition switch ON
      10.5 to 14 V
      L1-5 (2-4) - Body ground
      Ignition switch ON
      10.5 to 14 V

      If the voltage is not as specified, replace the 4WD control ECU (Click here). If the voltage is normal, replace the 4WD control switch.