AIR SWITCHING VALVE > INSTALLATION |
| 1. INSTALL NO. 3 AIR TUBE |
![]() |
Install a new gasket and the No. 3 air tube with the 2 bolts.
| 2. INSTALL NO. 2 AIR TUBE |
![]() |
Install a new gasket and the No. 2 air tube with the 2 bolts.
| 3. INSTALL ELECTRIC AIR CONTROL VALVE ASSEMBLY |
![]() |
Install the electric air control valve assembly with the 3 bolts.
Connect the 2 electric air control valve connectors.
![]() |
Install the bracket with the bolt.
Connect the knock sensor connector.
| 4. INSTALL AIR PIPE SUB-ASSEMBLY |
Connect the 2 No. 1 air hoses to the air pipe.
![]() |
Connect the air pipe to the electric air control valve assembly, and install the air pipe with the 2 bolts.
![]() |
Connect the air pump connector clamp holder.
Attach the wire harness claw.
Connect the electric air control valve connector.
Connect the No. 2 air injection system hose and No. 3 air injection system hose.
| 5. INSTALL FRONT WATER BY-PASS JOINT |
![]() |
Install 2 new gaskets and the front water by-pass joint with the 4 nuts.
Connect the engine coolant temperature sensor connector.
| 6. CONNECT WATER BY-PASS PIPE HOSE (w/ Trailer Towing System) |
![]() |
Connect the water by-pass pipe hose with the 3 bolts.
| 7. CONNECT NO. 2 WATER BY-PASS HOSE |
![]() |
Connect the No. 2 water by-pass hose to the water by-pass joint.
| 8. CONNECT NO. 1 WATER BY-PASS HOSE |
Connect the No. 1 water by-pass hose to the water by-pass joint and water inlet housing.
| 9. INSTALL NO. 1 ENGINE COVER |
![]() |
Install the No. 1 engine cover.
| 10. CONNECT FUEL TUBE CLAMP |
![]() |
Connect the fuel tube clamp to the bracket.
| 11. INSTALL NO. 2 CYLINDER HEAD COVER |
![]() |
Install the No. 2 cylinder head cover.
| 12. INSTALL FAN SHROUD (w/ Trailer Towing System) |
![]() |
Install the fan pulley to the fan bracket.
Place the shroud together with the coupling fan between the radiator and engine.
Temporarily install the fluid coupling fan to the fan bracket with the 4 nuts. Tighten the nuts as much as possible by hand.
![]() |
Attach the shroud claws to the radiator as shown in the illustration.
Install the shroud with the 2 bolts.
Connect the reservoir hose to the upper radiator tank.
![]() |
Pass the 2 hoses through the flexible hose clamp and close the clamp as shown in the illustration.
Install the fan and generator V belt .
Tighten the 4 nuts of the fluid coupling fan.
| 13. INSTALL FAN SHROUD (w/o Trailer Towing System) |
![]() |
Install the fan pulley to the fan bracket.
Place the shroud together with the coupling fan between the radiator and engine.
Temporarily install the fluid coupling fan to the fan bracket with the 4 nuts. Tighten the nuts as much as possible by hand.
![]() |
Attach the shroud claws to the radiator as shown in the illustration.
Install the shroud with the 2 bolts.
Connect the reservoir hose to the upper radiator tank.
Install the fan and generator V belt .
Tighten the 4 nuts of the fluid coupling fan.
| 14. INSTALL OUTLET RADIATOR HOSE |
![]() |
Connect the outlet radiator hose to the water inlet housing.
| 15. INSTALL INLET RADIATOR HOSE |
![]() |
Install the inlet radiator hose.
| 16. INSTALL INTAKE MANIFOLD |
Install the intake manifold (Click here).
| 17. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY |
Install the exhaust manifold (Click here).