SFI SYSTEM > Fuel Injector Circuit |

| 1.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the fuel injector connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Cylinder No. | Tester Connection | Switch Condition | Specified Condition |
| No. 1 | D60-1 - Ground | Ignition switch ON | 11 to 14 V |
| No. 2 | D67-1 - Ground | Ignition switch ON | 11 to 14 V |
| No. 3 | D61-1 - Ground | Ignition switch ON | 11 to 14 V |
| No. 4 | D66-1 - Ground | Ignition switch ON | 11 to 14 V |
| No. 5 | D62-1 - Ground | Ignition switch ON | 11 to 14 V |
| No. 6 | D65-1 - Ground | Ignition switch ON | 11 to 14 V |
| No. 7 | D63-1 - Ground | Ignition switch ON | 11 to 14 V |
| No. 8 | D64-1 - Ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 2.INSPECT FUEL INJECTOR ASSEMBLY |
Inspect the fuel injector (Click here).
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM) |
![]() |
Disconnect the fuel injector connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Cylinder | Tester Connection | Condition | Specified Condition |
| No. 1 | D60-2 - Body ground | Always | 10 kΩ or higher |
| D60-2 - D56-86 (#10) | Always | Below 1 Ω | |
| No. 2 | D67-2 - Body ground | Always | 10 kΩ or higher |
| D67-2 - D56-109 (#20) | Always | Below 1 Ω | |
| No. 3 | D61-2 - Body ground | Always | 10 kΩ or higher |
| D61-2 - D56-85 (#30) | Always | Below 1 Ω | |
| No. 4 | D66-2 - Body ground | Always | 10 kΩ or higher |
| D66-2 - D56-108 (#40) | Always | Below 1 Ω | |
| No. 5 | D62-2 - Body ground | Always | 10 kΩ or higher |
| D62-2 - D56-84 (#50) | Always | Below 1 Ω | |
| No. 6 | D65-2 - Body ground | Always | 10 kΩ or higher |
| D65-2 - D56-107 (#60) | Always | Below 1 Ω | |
| No. 7 | D63-2 - Body ground | Always | 10 kΩ or higher |
| D63-2 - D56-83 (#70) | Always | Below 1 Ω | |
| No. 8 | D64-2 - Body ground | Always | 10 kΩ or higher |
| D64-2 - D56-106 (#80) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 4.INSPECT FUSE (INJ, IG2 MAIN) |
![]() |
Remove the INJ fuse and IG2 MAIN fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| INJ fuse | Always | Below 1 Ω |
| IG2 fuse | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.INSPECT INTEGRATION RELAY (IG2) |
Inspect the integration relay .
|
| ||||
| OK | ||
| ||