Home › Engine / Hybrid System · 3UR-FBE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > Fuel Injector Circuit

for Preparation Click here


DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM


A179943E01


INSPECTION PROCEDURE

1.INSPECT INJECTOR ASSEMBLY (POWER SOURCE)
A198845E01
  1. Disconnect the injector connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    d1-2 - Ground
    Ignition switch ON
    11 to 14 V
    No. 2
    c1-2 - Ground
    Ignition switch ON
    11 to 14 V
    No. 3
    d2-2 - Ground
    Ignition switch ON
    11 to 14 V
    No. 4
    c2-2 - Ground
    Ignition switch ON
    11 to 14 V
    No. 5
    d3-2 - Ground
    Ignition switch ON
    11 to 14 V
    No. 6
    c3-2 - Ground
    Ignition switch ON
    11 to 14 V
    No. 7
    d4-2 - Ground
    Ignition switch ON
    11 to 14 V
    No. 8
    c4-2 - Ground
    Ignition switch ON
    11 to 14 V



NG
Go to step 4
OK


2.INSPECT INJECTOR ASSEMBLY
  1. Inspect the injector .



NG
REPLACE INJECTOR ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)
A198846E01
  1. Disconnect the injector connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    d1-1 - Body ground
    Always
    10 kΩ or higher
    d1-1 - D56-86 (#10)
    Always
    Below 1 Ω
    No. 2
    c1-1 - Ground
    Always
    10 kΩ or higher
    c1-1 - D56-109 (#20)
    Always
    Below 1 Ω
    No. 3
    d2-1 - Ground
    Always
    10 kΩ or higher
    d2-1 - D56-85 (#30)
    Always
    Below 1 Ω
    No. 4
    c2-1 - Ground
    Always
    10 kΩ or higher
    c2-1 - D56-108 (#40)
    Always
    Below 1 Ω
    No. 5
    d3-1 - Ground
    Always
    10 kΩ or higher
    d3-1 - D56-84 (#50)
    Always
    Below 1 Ω
    No. 6
    c3-1 - Ground
    Always
    10 kΩ or higher
    c3-1 - D56-107 (#60)
    Always
    Below 1 Ω
    No. 7
    d4-1 - Ground
    Always
    10 kΩ or higher
    d4-1 - D56-83 (#70)
    Always
    Below 1 Ω
    No. 8
    c4-1 - Ground
    Always
    10 kΩ or higher
    c4-1 - D56-106 (#80)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

4.INSPECT FUSES (INJ, IG2 MAIN)
A166990E01
  1. Remove the INJ fuse and IG2 MAIN fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    INJ fuse
    Always
    Below 1 Ω
    IG2 fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


5.INSPECT INTEGRATION RELAY (IG2)
  1. Inspect the integration relay .



NG
REPLACE INTEGRATION RELAY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - INJECTOR ASSEMBLY)