Home › Audio/Visual/Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM

REAR SEAT ENTERTAINMENT SYSTEM > Sound Signal Circuit between Headphone Terminal and Television Display

for Preparation Click here


DESCRIPTION

This circuit sends a sound signal from the television display to the headphone.

WIRING DIAGRAM


E160632E01


INSPECTION PROCEDURE

1.CHECK HEADPHONE
  1. Check the malfunctioning headphones.
    Result 
    Result
    Proceed to
    Malfunction in headphone RH side
    A
    Malfunction in headphone LH side
    B



B
Go to step 4
A


2.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - HEADPHONE JACK RH)


    E160633E01
  1. Disconnect the U2 television display assembly connector.

  1. Disconnect the S7 headphone jack RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U2-3 (HP2R) - S7-1 (HP2R)
    Always
    Below 1 Ω
    U2-19 (HP2L) - S7-2 (HP2L)
    U2-4 (SLD2) - S7-3 (SG8)
    U2-3 (HP2R) - Body ground
    Always
    10 kΩ or higher
    U2-19 (HP2L) - Body ground
    U2-4 (SLD2) - Body ground

  1. Reconnect the television display assembly connector.

  1. Reconnect the headphone jack RH connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT TELEVISION DISPLAY ASSEMBLY


    E160634E01
  1. Using an oscilloscope, check the waveform between each terminal and the body ground according to the conditions, as shown in the table below.

    OK: Waveform:
    Tester Connection
    Condition
    Specified Condition
    U2-3 (HP2R) - Body ground
    Audio sound is being produced
    A waveform synchronized with sound is output
    U2-19 (HP2L) - Body ground



NG
REPLACE TELEVISION DISPLAY ASSEMBLY (Click here)
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

4.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - HEADPHONE JACK LH)


    E160633E02
  1. Disconnect the U2 television display assembly connector.

  1. Disconnect the S8 headphone jack LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U2-5 (HP1R) - S8-1 (HP1R)
    Always
    Below 1 Ω
    U2-21 (HP1L) - S8-2 (HP1L)
    U2-20 (SLD1) - S8-3 (SG7)
    U2-5 (HP1R) - Body ground
    Always
    10 kΩ or higher
    U2-21 (HP1L) - Body ground
    U2-20 (SLD1) - Body ground

  1. Reconnect the television display assembly connector.

  1. Reconnect the headphone jack LH connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT TELEVISION DISPLAY ASSEMBLY


    E160634E02
  1. Using an oscilloscope, check the waveform between each terminal and the body ground according to the conditions, as shown in the table below.

    OK: Waveform:
    Tester Connection
    Condition
    Specified Condition
    U2-5 (HP1R) - Body ground
    Audio sound is being produced
    A waveform synchronized with sound is output
    U2-21 (HP1L) - Body ground



NG
REPLACE TELEVISION DISPLAY ASSEMBLY (Click here)
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)