Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER

REAR SHOCK ABSORBER > INSTALLATION

for Preparation Click here



1. TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY LH


C180767
  1. Temporarily install the upper side of the shock absorber to the chassis frame with the bolt and nut.

  1. Temporarily install the lower side of the shock absorber to the lower suspension arm with the bolt.



    C180604
  1. Connect the AVS connector (w/ AVS).



2. INSTALL REAR STABILIZER BAR
(Click here)


3. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH


C180589
  1. Install the rear height control sensor with the nut.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Connect the rear height control sensor connector.



    C180588
  1. Align the matchmark on the rear height control sensor link and bracket.

  1. Install the rear height control sensor link with the nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



4. INSTALL PROPELLER SHAFT ASSEMBLY (for 2WD)
(Click here)


5. INSTALL PROPELLER SHAFT ASSEMBLY (for 4WD)


    C179258E01
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Align the matchmarks on the propeller shaft flange and transfer flange.

  1. Install the propeller shaft assembly with the 8 nuts.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }



6. INSTALL TRANSFER HEAT INSULATOR (for 4WD)


    C158451
  1. Install the transfer heat insulator with the 3 bolts.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }



7. INSTALL PROPELLER SHAFT HEAT INSULATOR (for 4WD)


    C158450
  1. Install the propeller shaft heat insulator with the 2 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



8. INSTALL TAIL EXHAUST PIPE ASSEMBLY (for 3UR-FE)
  1. Connect the tailpipe to the exhaust pipe support.



    A184938E01
  1. Install a new gasket to the center exhaust pipe.

  1. Connect the tailpipe to the center exhaust pipe.

  1. Attach a new clamp to the tailpipe and center exhaust pipe. Then install the bolt to the clamp.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

    HINT:
    Install the clamp within the angle range shown in the illustration.



9. INSTALL TAIL EXHAUST PIPE ASSEMBLY (for 2UZ-FE)


    A151854E05
  1. Install the new gasket to the center exhaust pipe assembly.

  1. Connect the tail exhaust pipe assembly to the exhaust pipe support.

  1. Install the tail exhaust pipe assembly with the new clamp.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

    HINT:
    Install the clamp within the angle range shown in the illustration.



10. INSTALL REAR WHEEL
  1. for Aluminum Wheel

Torque:
131 N*m{ 1336 kgf*cm , 97 ft.*lbf }

  1. for Steel Wheel

Torque:
209 N*m{ 2131 kgf*cm , 154 ft.*lbf }



11. STABILIZE SUSPENSION
  1. Lower the vehicle.

  1. Press down on the vehicle several times to stabilize the suspension.



12. TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH


C180767E01
  1. Tighten the 2 bolts and nut.

    1. for bolt and nut A

    Torque:
    135 N*m{ 1377 kgf*cm , 100 ft.*lbf }

    1. for bolt B

    Torque:
    90 N*m{ 918 kgf*cm , 67 ft.*lbf }



13. INSPECT AND ADJUST REAR WHEEL ALIGNMENT
(Click here)