Home › Vehicle Interior › SEAT BELT › REAR NO. 1 SEAT OUTER BELT ASSEMBLY

REAR NO. 1 SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below is for the RH side.



1. INSTALL REAR NO. 1 SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    B194786
  1. Align the rear No. 1 shoulder belt anchor adjuster positioning claw with the hole, and install the rear No. 1 shoulder belt anchor adjuster with the 2 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



2. INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH


    B194785E01
  1. Align the claws on the body with the rear No. 1 seat outer belt retractor positioning holes.

  1. Install the rear No. 1 seat outer belt with the 2 bolts.

    HINT:
    First install bolt A, and then install bolt B.

    1. for Bolt A

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    1. for Bolt B

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B194784
  1. Install the shoulder anchor to the shoulder belt anchor adjuster with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



3. INSTALL REAR SIDE NO. 2 AIR DUCT


    I104300
  1. Install the air duct with the 2 clips.



4. INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY RH


    B190124
  1. Pass the rear seat outer belt floor anchor through the quarter trim panel.

  1. Engage the 5 clips and install the rear window side garnish.

  1. Install the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B193066
  1. Engage the claw and install the cover.



5. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Manual Seat)


  1. Connect the connector.


    B190143

  1. Engage the 12 clips and install the quarter trim panel assembly.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Engage the 2 clips.



    B190147
  1. Engage the 2 claws and install the cover.



    B190146
  1. Install the outer lap belt anchor with bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190158
  1. Install the outer lap belt anchor with bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190145
  1. Engage the 3 claws to install the outer lap belt anchor cover.



6. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat)


  1. Connect the 3 connectors.


    B191799

  1. Engage the 12 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Engage the 2 clips.



    B190147
  1. Engage the 2 claws and install the cover.



    B190146
  1. Install the outer lap belt anchor with bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190158
  1. Install the outer lap belt anchor with bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190145
  1. Engage the 3 claws to install the outer lap belt anchor cover.



7. INSTALL REAR FLOOR MAT SUPPORT PLATE


    B190142
  1. Engage the 5 clips and the 4 claws, and install the rear floor mat support plate.



8. INSTALL ROPE HOOK ASSEMBLY


    B190141
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B190139
  1. Engage the 2 claws and install the cover.



9. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B190154E01
  1. Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.
    Paint Mark 
    Area
    Color
    RH side
    Pink
    LH side
    Purple



10. INSTALL REAR DOOR SCUFF PLATE RH


    B186666
  1. Engage the 2 claws and 5 clips to install the rear door scuff plate.

  1. Install the 2 bolts.



    B186665
  1. Engage the 6 claws and the 5 clips and the 2 guides, and install the rear door scuff plate.

  1. Install the screw.



11. INSTALL REAR FLOOR STEP NO. 1 COVER


    B191404
  1. Engage the 2 claws and install the rear floor step No. 1 cover.



12. INSTALL REAR FLOOR STEP NO. 2 COVER


    B193890
  1. Engage the 2 claws and the install the rear floor step No. 2 cover.



13. INSTALL REAR SEAT CUSHION HINGE LOWER COVER RH


    B191794
  1. Engage the 2 clips and the 5 claws, and install the rear cushion hinge lower cover RH.



14. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Manual Seat)
  1. Install the rear No. 2 seat assembly (Click here).



15. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Power Seat)
  1. Install the rear No. 2 seat assembly (Click here).