Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1241/41    Low Battery Positive Voltage or Abnormally High Battery Positive Voltage

for Preparation Click here


DESCRIPTION

When there is an abnormality in the power supply circuit of the VSC actuator (skid control ECU), the skid control ECU sets a DTC and the operation is prohibited by the fail-safe function. This DTC is set when the voltage supplied to terminal +BS is outside the DTC detection threshold due to abnormalities of the battery, power source circuits or charging circuits such as the alternator circuit.
The fail-safe function is canceled when the voltage to terminal +BS returns to normal.

HINT:
If the vehicle speed is 20 km/h (12 mph) or less when the battery voltage is low, the ABS warning light and slip indicator light illuminate. However, a DTC will not be output.


DTC Code
DTC Detection Condition
Trouble Area
C1241/41
When any of following conditions detected:
  1. +BS terminal voltage 18 V or more (momentary occurrence included).
  2. At vehicle speed 20 km/h (12 mph) or more, +BS terminal voltage 9.7 V or less for 0.21 seconds or more.
  3. At vehicle speed 20 km/h (12 mph) or more, +BS terminal voltage 8.5 V or less (momentary occurrence included).
  1. ABS2 H-fuse
  2. Battery
  3. Charging system
  4. Power source circuit
  5. VSC actuator (skid control ECU)

WIRING DIAGRAM

Refer to DTC C0278/11 .

INSPECTION PROCEDURE

NOTICE:
When replacing the VSC actuator assembly, perform zero point calibration (Click here).

1.INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1UR-FE)
    B
    NG (for 3UR-FE)
    C
    NG (for 3UR-FBE)
    D



B
CHECK CHARGING SYSTEM (Click here)

C
CHECK CHARGING SYSTEM (Click here)

D
CHECK CHARGING SYSTEM (Click here)
A


2.INSPECT FUSE (ABS2)


    C152723E03
  1. Remove the ABS2 H-fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ABS2 H-fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)


    C240470E02
  1. Disconnect the A19 ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A19-32 (+BS) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A19-16 (GND1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Check if the same DTCs are output (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)
A

REPLACE VSC ACTUATOR ASSEMBLY (Click here)