Home › Engine / Hybrid System ยท 1UR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P2119    Throttle Actuator Control Throttle Body Range / Performance

for Preparation Click here


DESCRIPTION

The Electronic Throttle Control System (ETCS) is composed of the throttle actuator, Throttle Position (TP) sensor, Accelerator Pedal Position (APP) sensor, and ECM. The ECM operates the throttle actuator to regulate the throttle valve in response to driver inputs. The TP sensor detects the opening angle of the throttle valve, and provides the ECM with feedback so that the throttle valve can be appropriately controlled by the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P2119
Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic)
  1. ETCS
  2. ECM
  3. Wire harness or connector

MONITOR DESCRIPTION

The ECM determines the actual opening angle of the throttle valve from the TP sensor signal. The actual opening angle is compared to the target opening angle commanded by the ECM. If the difference between these two values is outside the standard range, the ECM interprets this as a malfunction in the ETCS. The ECM then illuminates the MIL and stores the DTC.
If the malfunction is not repaired successfully, the DTC is stored when the accelerator pedal is quickly released (to close the throttle valve) after the engine speed reaches 5000 rpm by the accelerator pedal being fully depressed (fully open the throttle valve).

MONITOR STRATEGY


Related DTCs
P2119: ETCS malfunction
Required Sensors/Components (Main)
Throttle actuator
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
Within 1 second
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
System guard*
ON
*: System guard is ON when the following conditions met
-
Throttle actuator
ON
Throttle actuator duty calculation
Executing
Throttle position sensor fail
Not detected
Throttle actuator current-cut operation
Not executing
Throttle actuator power supply
4 V or higher
Throttle actuator fail
Not detected

TYPICAL MALFUNCTION THRESHOLDS


Either of following conditions A or B met
-
A. Difference between commanded closed throttle position and current closed throttle position
0.3 V or more for 1 second
B. Difference between commanded open throttle position and current open throttle position
0.3 V or more for 0.6 seconds

CONFIRMATION DRIVING PATTERN


A199316E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine.
  7. Idle the engine for 20 seconds.
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P2119.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, fully depress and release the accelerator pedal 3 times, and then check the DTC judgment result [C].

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


FAIL-SAFE

When this DTC or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal opening angle to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

Refer to DTC P2102 .

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Refer to "Data List / Active Test" [Throttle Position Commanded, Throttle Position No. 1, Throttle Motor Current, Throttle Motor Duty (Open) and Throttle Motor Duty (Close)] (Click here).

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2119)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    DTC P2119 is output
    A
    DTC P2119 and others are output
    B

    HINT:
    If any DTCs other than P2119 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (THROTTLE POSITION)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position Command.

  1. Check the values displayed on the Techstream while fully depressing and releasing the accelerator pedal quickly.
    Result 
    Result
    Proceed to
    Throttle Position No. 1 does not change
    A
    Throttle Position No. 1 change even a little
    B

    HINT:
    When a DTC is output, the system changes to fail-safe mode. Therefore, only use the data up until the time the DTC is stored for confirmation.



B
Go to step 4
A


3.INSPECT THROTTLE BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
  1. Inspect the throttle body assembly (Click here).



NG
Go to step 7
OK


4.INSPECT THROTTLE BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
  1. Check for contamination between the throttle valve and housing. If necessary, clean the throttle body. Also, check that the throttle valve moves smoothly.

OK:
Throttle valve is not contaminated with foreign objects and moves smoothly.



NG
Go to step 7
OK


5.READ VALUE USING TECHSTREAM (THROTTLE POSITION)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.

  1. Check the values displayed on the Techstream while wiggling the ECM wire harness.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Check for DTCs.
    Result 
    Result
    Proceed to
    Value in Data List changes when wire harness is wiggled, or DTC is output*
    A
    Other than above
    B
    *: As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (Click here).



B
Go to step 8
A


6.REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE BODY - ECM)
  1. As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (See page ).


NEXT

END 

7.REPLACE THROTTLE BODY ASSEMBLY
  1. Replace the throttle body assembly (Click here).


NEXT


8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2119)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Allow the engine to idle for 15 seconds or more.

  1. Fully depress and release the accelerator pedal several times quickly.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Check DTCs.
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P2119 is output
    B



B
REPLACE ECM (Click here)
A

END