Home › Engine / Hybrid System · 1UR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P2120    Throttle / Pedal Position Sensor / Switch "D" Circuit

DTC    P2122    Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input

DTC    P2123    Throttle / Pedal Position Sensor / Switch "D" Circuit High Input

DTC    P2125    Throttle / Pedal Position Sensor / Switch "E" Circuit

DTC    P2127    Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input

DTC    P2128    Throttle / Pedal Position Sensor / Switch "E" Circuit High Input

DTC    P2138    Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation

for Preparation Click here


DESCRIPTION

The APP sensor is mounted on the accelerator pedal bracket and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.5 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the APP sensor itself.
The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.

HINT:
This ETCS (Electronic Throttle Control System) does not use a throttle cable.


A112620E11


DTC No.
DTC Detection Condition
Trouble Area
P2120
VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic)
  1. APP sensor
  1. ECM
P2122
VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic)
  1. APP sensor
  1. Open in VCP1 circuit
  1. Open or ground short in VPA circuit
  1. ECM
P2123
VPA 4.8 V or more for 2.0 seconds or more
(1 trip detection logic)
  1. APP sensor
  1. Open in EPA circuit
  1. ECM
P2125
VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic)
  1. APP sensor
  1. ECM
P2127
VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic)
  1. APP sensor
  1. Open in VCP2 circuit
  1. Open or ground short in VPA2 circuit
  1. ECM
P2128
Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic):
(a) VPA2 4.8 V or more
(b) VPA between 0.4 V and 3.45 V
  1. APP sensor
  1. Open in EPA2 circuit
  1. ECM
P2138
Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic):
(a) Difference between VPA and VPA2 0.02 V or less
(b) VPA 0.4 V or less and VPA2 1.2 V or less
  1. Short between VPA and VPA2 circuits
  1. APP sensor
  1. ECM

HINT:
When any of these DTCs are stored, check the APP sensor voltage by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

Trouble Area
Accel Sensor Out No. 1
When AP Released
Accel Sensor Out No. 2
When AP Released
Accel Sensor Out No. 1
When AP Depressed
Accel Sensor Out No. 2
When AP Depressed
VCP circuit open
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
Open or ground short in VPA circuit
0 to 0.2 V
1.2 to 2.0 V
0 to 0.2 V
3.4 to 4.7 V
Open or ground short in VPA2 circuit
0.5 to 1.1 V
0 to 0.2 V
2.6 to 4.5 V
0 to 0.2 V
EPA circuit open
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
Normal condition
0.5 to 1.1 V
1.2 to 2.0 V
2.6 to 4.5 V
3.4 to 4.7 V

HINT:
  1. Accelerator pedal positions are expressed as voltages.
  1. AP stands for Accelerator Pedal.


MONITOR DESCRIPTION

When the output voltage of either VPA or VPA2 deviates from the standard range, or the difference between the output voltages of the 2 sensor circuits is less than the threshold, the ECM determines that there is a malfunction in the APP sensor. The ECM then illuminates the MIL and stores a DTC.
Example:
When the output voltage of VPA drops below 0.4 V for more than 0.5 seconds when the accelerator pedal is fully depressed, DTC P2122 is stored.
If the malfunction is not repaired successfully, a DTC is stored 2 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P2120: APP sensor 1 range check (fluctuating)
P2122: APP sensor 1 range check (low voltage)
P2123: APP sensor 1 range check (high voltage)
P2125: APP sensor 2 range check (fluctuating)
P2127: APP sensor 2 range check (low voltage)
P2128: APP sensor 2 range check (high voltage)
P2138: APP sensor range check (correlation)
Required Sensors/Components (Main)
APP sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds: P2120, P2122, P2125 and P2127
2.0 seconds: P2123, P2128 and P2138
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Either of following conditions 1 or 2 met:
-
1. Ignition switch
ON
2. Throttle actuator power
ON

TYPICAL MALFUNCTION THRESHOLDS


P2120 
Either of following conditions 1 or 2 met:
-
1. VPA voltage when VPA2 voltage 0.04 V or more
0.4 V or less
2. VPA voltage
4.8 V or more

P2122 
VPA voltage when VPA2 voltage 0.04 V or more
0.4 V or less

P2123 
VPA voltage
4.8 V or more

P2125 
Either of following conditions 1 or 2 met:
-
1. VPA2 voltage when VPA voltage 0.04 V or more
1.2 V or less
2. VPA2 voltage when VPA voltage 0.4 to 3.45 V
4.8 V or more

P2127 
VPA2 voltage when VPA voltage 0.04 V or more
1.2 V or less

P2128 
VPA2 voltage when VPA voltage 0.4 to 3.45 V
4.8 V or more

P2138 
Either of following conditions A or B met:
-
Condition A
-
Difference between VPA and VPA 2 voltages
0.02 V or less
Condition B
-
VPA voltage
0.4 V or less
VPA2 voltage
1.2 V or less

COMPONENT OPERATING RANGE


VPA voltage
0.4 to 4.8 V
VPA2 voltage
1.2 to 4.8 V
Difference between VPA and VPA2 voltages
More than 0.02 V

CONFIRMATION DRIVING PATTERN


A199317E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Fully depress and release the accelerator pedal [B].
  7. Check that 5 seconds or more have elapsed since the ignition switch was turned to ON.
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P2120, P2122, P2123, P2125, P2127, P2128 or P2138.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


FAIL-SAFE

When DTC P2120, P2121, P2122, P2123, P2125, P2127, P2128 or P2138 is stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM


A185023E01


INSPECTION PROCEDURE

HINT:
  1. These DTCs relate to the Accelerator Pedal Position (APP) sensor.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (ACCELERATOR POSITION SENSOR)
FI07052E42
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

  1. Read the values displayed on the Techstream.

    Standard Voltage:
    Accelerator Pedal Operation
    Accel Sensor Out No. 1
    Accel Sensor Out No. 2
    Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2
    Released
    0.5 to 1.1 V
    1.2 to 2.0 V
    More than 0.02 V
    Depressed
    2.6 to 4.5 V
    3.4 to 4.7 V

Text in Illustration 
*a
Depressed
*b
Released
Result 
Result
Proceed to
NG
A
OK
B


B
Go to step 5
A


2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
  1. Disconnect the APP sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A17-6 (VPA) - A27-55 (VPA)
    Always
    Below 1 Ω
    A17-5 (EPA) - A27-58 (EPA)
    Always
    Below 1 Ω
    A17-4 (VCPA) - A27-57 (VCPA)
    Always
    Below 1 Ω
    A17-3 (VPA2) - A27-56 (VPA2)
    Always
    Below 1 Ω
    A17-2 (EPA2) - A27-60 (EPA2)
    Always
    Below 1 Ω
    A17-1 (VCP2) - A27-59 (VCP2)
    Always
    Below 1 Ω
    A17-6 (VPA) or A27-55 (VPA) - Body ground
    Always
    10 kΩ or higher
    A17-5 (EPA) or A27-58 (EPA) - Body ground
    Always
    10 kΩ or higher
    A17-4 (VCPA) or A27-57 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A17-3 (VPA2) or A27-56 (VPA2) - Body ground
    Always
    10 kΩ or higher
    A17-2 (EPA2) or A27-60 (EPA2) - Body ground
    Always
    10 kΩ or higher
    A17-1 (VCP2) or A27-59 (VCP2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ECM (VCPA AND VCP2 VOLTAGE)
A115666E95
  1. Disconnect the APP sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A17-4 (VCPA) - A17-5 (EPA)
    Ignition switch ON
    4.5 to 5.5 V
    A17-1 (VCP2) - A17-2 (EPA2)
    Ignition switch ON
    4.5 to 5.5 V

Text in Illustration 
*a
Front view of wire harness connector
(to APP Sensor)


NG
REPLACE ECM (Click here)
OK


4.REPLACE ACCELERATOR PEDAL ASSEMBLY
  1. Replace the accelerator pedal assembly (Click here).


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    DTC P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 is output
    A
    DTC is not output
    B



B
END
A

REPLACE ECM (Click here)