Home › Engine / Hybrid System · 3UR-FBE › ENGINE CONTROL › SFI SYSTEM

DTC    P0230    Fuel Pump Primary Circuit

for Preparation Click here


DESCRIPTION

When a malfunction in the fuel pump circuit is detected, DTC P0230 is stored.
The fuel pump circuit consists of the ECM, fuel pump and fuel pump ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump ECU. Based on the signal sent from the ECM, the fuel pump ECU adjusts the fuel pump operation speed between 3 settings. The fuel pump ECU also has a self-diagnosis function. Based on the fuel pump circuit condition, the fuel pump ECU outputs a diagnostic signal (DI) to the ECM, and the ECM determines if there is a malfunction in the fuel pump circuit.

DTC No.
DTC Detection Condition
Trouble Area
P0230
When either condition below is met (1 trip detection logic):
  1. When fuel pump is operating:
    1. Remaining fuel is 17 L or more
    2. DI terminal output is low
  2. When fuel pump is not operating:
    1. DI terminal output is high
  1. Open or short in fuel pump circuit
  2. Fuel pump
  3. Fuel pump ECU
  4. ECM

MONITOR DESCRIPTION

To monitor the fuel pump circuit, the ECM checks the fuel pump control signal (FPC) and diagnostic signal (DI). The FPC voltage varies between approximately 0 V to approximately 12 V (duty signal). Based on the condition of the fuel pump ECU malfunction, the DI voltage varies between approximately 0 V and approximately 12 V. The ECM then compares the variance of the FPC voltage and DI voltage, and determines if the fuel pump circuit is malfunctioning. When the ECM determines that the fuel pump circuit is malfunctioning, a DTC is set immediately.

WIRING DIAGRAM


A179936E01


INSPECTION PROCEDURE

This troubleshooting procedure is based on the premise that the engine is started. If the engine is not started, proceed to the problem symptoms table (Click here).
1.CHECK FOR DTC (B1500)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Combination Meter / Trouble Codes.

  1. Read the DTC.
    Result 
    Result
    Proceed to
    DTC B1500 is not output
    A
    DTC B1500 is output
    B



B
GO TO DTC B1500 (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (FUEL PUMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check whether operating sounds can be heard while operating the relay using the Techstream.

    OK:
    Operating sounds can be heard from relay.



NG
Go to step 6
OK


3.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND)
A162652E13
  1. Disconnect the O35 fuel pump ECU connector.

  1. Disconnect the A27 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O35-1 (FPC) - A27-52 (FPC)
    Always
    Below 1 Ω
    O35-2 (DI) - A27-18 (DI)
    Always
    Below 1 Ω
    O35-3 (E) - Body ground
    Always
    Below 1 Ω
    O35-1 (FPC) or A27-52 (FPC) - Body ground
    Always
    10 kΩ or more
    O35-2 (DI) or A27-18 (DI) - Body ground
    Always
    10 kΩ or more



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.REPLACE FUEL PUMP ECU
  1. Replace the fuel pump ECU (Click here).


NEXT


5.CONFIRM WHETHER DTC OUTPUT RECURS
  1. Check that there is 17 L or more of fuel remaining.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Cranking it for 15 seconds.

  1. Idle it for 1 minute.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0230 is output
    B



B
REPLACE ECM (Click here)
A

END 

6.INSPECT CIRCUIT OPENING RELAY (C/OPN)
E145692E01
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When no battery voltage applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE CIRCUIT OPENING RELAY (C/OPN)
OK


7.INSPECT CIRCUIT OPENING RELAY (POWER SOURCE VOLTAGE)
A162278E01
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C/OPN relay (2) - Body ground
    Ignition switch ON
    11 to 14 V
    C/OPN relay (5) - Body ground
    Ignition switch ON
    11 to 14 V



NG
Go to step 14
OK


8.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - ECM, FUEL PUMP ECU)
A162653E09
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Disconnect the A27 ECM connector.

  1. Disconnect the O35 fuel pump ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay (1) - A27-48 (FC)
    Always
    Below 1 Ω
    C/OPN relay (3) - O35-4 (+B)
    Always
    Below 1 Ω
    C/OPN relay (1) or A27-48 (FC) - Body ground
    Always
    10 kΩ or higher
    C/OPN relay (3) or O35-4 (+B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)
A161830E05
  1. Disconnect the Q1 fuel pump connector.

  1. Disconnect the O36 fuel pump ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q1-4 (B2) - O36-1 (FP)
    Always
    Below 1 Ω
    Q1-5 (E2) - O36-2 (FP-)
    Always
    Below 1 Ω
    Q1-4 (B2) or O36-1 (FP) - Body ground
    Always
    10 kΩ or higher
    Q1-5 (E2) or O36-2 (FP-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT FUEL PUMP
  1. Inspect the fuel pump (Click here).



NG
REPLACE FUEL PUMP (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND)
A162652E14
  1. Disconnect the O35 fuel pump ECU connector.

  1. Disconnect the A27 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O35-1 (FPC) - A27-52 (FPC)
    Always
    Below 1 Ω
    O35-2 (DI) - A27-18 (DI)
    Always
    Below 1 Ω
    O35-3 (E) - Body ground
    Always
    Below 1 Ω
    O35-1 (FPC) or A27-52 (FPC) - Body ground
    Always
    10 kΩ or more
    O35-2 (DI) or A27-18 (DI) - Body ground
    Always
    10 kΩ or more



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.REPLACE FUEL PUMP ECU
  1. Replace the fuel pump ECU (Click here).


NEXT


13.CONFIRM WHETHER DTC OUTPUT RECURS
  1. Check that there is 17 liters (18 US qts, 15 Imp. qts) or more of fuel remaining.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Cranking it for 15 seconds.

  1. Idle it for 1 minute.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0230 is output
    B



B
REPLACE ECM (Click here)
A

END 

14.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - F/PMP RELAY, IGN FUSE)
A165847E01
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Remove the fuel pump relay (F/PMP) from the engine room relay block.

  1. Remove the IGN fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay (2) - IGN fuse (2)
    Always
    Below 1 Ω
    C/OPN relay (5) - F/PMP relay (3)
    Always
    Below 1 Ω
    C/OPN relay (2) or IGN fuse (2) - Body ground
    Always
    10 kΩ or more
    C/OPN relay (5) or F/PMP relay (3) - Body ground
    Always
    10 kΩ or more



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.INSPECT FUEL PUMP RELAY (F/PMP)
E145692E01
  1. Remove the fuel pump relay (F/PMP) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When no battery voltage applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE FUEL PUMP RELAY (F/PMP)
OK


16.CHECK HARNESS AND CONNECTOR (F/PMP RELAY - INTEGRATION RELAY, BATTERY, BODY GROUND)
A165848E01
  1. Remove the F/PMP fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F/PMP fuse
    Always
    Below 1 Ω

  1. Reinstall the F/PMP fuse.

  1. Remove the fuel pump relay (F/PMP) from the engine room relay block.

  1. Remove the integration relay from the engine room relay block.

  1. Disconnect the 1B integration relay connector.

  1. Disconnect the cable from the battery positive (+) terminal.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F/PMP relay (1) - 1B-4
    Always
    Below 1 Ω
    F/PMP relay (5) - Positive (+) battery cable
    Always
    Below 1 Ω
    F/PMP relay (2) - Body ground
    Always
    Below 1 Ω
    F/PMP relay (1) or 1B-4 - Body ground
    Always
    10 kΩ or higher
    F/PMP relay (5) or Positive (+) battery cable - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)