DTC P0335 Crankshaft Position Sensor "A" Circuit |
DTC P0337 Crankshaft Position Sensor "A" Circuit Low Input |
DTC P0338 Crankshaft Position Sensor "A" Circuit High Input |
DTC P0339 Crankshaft Position Sensor "A" Circuit Intermittent |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0335 |
|
|
| P0337 | Output voltage of CKP sensor 0.3 V or less for 4 seconds (1 trip detection logic) |
|
| P0338 | Output voltage of CKP sensor 4.7 V or more for 4 seconds (1 trip detection logic) |
|
| P0339 | Under conditions (a), (b) and (c), no CKP sensor signal to ECM for 0.05 seconds or more (1 trip detection logic): (a) Engine speed 1000 rpm or more (b) Starter signal OFF (c) 3 seconds or more have elapsed since starter signal switched from ON to OFF |
|
![]() |
| Tester Connection | Tool Setting | Condition | Specified Condition |
| D56-110 (NE+) - D56-111 (NE-) | 5 V/DIV., 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| D56-90 (G2) - D56-89 (G2-) | 5 V/DIV., 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| Related DTCs | P0335: Crankshaft position sensor range check/rationality P0337: Crankshaft position sensor check (Low voltage) P0338: Crankshaft position sensor check (High voltage) |
| Required sensors/Components (Main) | Crankshaft Position (CKP) sensor |
| Required sensors/Components (Related) | Camshaft position sensor |
| Frequency of operation | Continuous |
| Duration | P0335: 15 seconds P0337, P0338: 4 seconds |
| MIL operation | Immediate |
| Sequence of operation | None |
| Monitor runs whenever following DTCs not stored | None |
| Battery voltage | Higher than 6 V |
| CKP sensor voltage | 0.3 to 4.7 V |
| Ignition switch | ON |
| Starter | ON |
| Minimum battery voltage while starter ON | Below 11 V |
| Battery voltage | Higher than 6 V |
| CKP sensor voltage | 0.3 to 4.7 V |
| Ignition switch | ON |
| Engine speed | 450 rpm or higher |
| Starter | OFF |
| Time after starter turned from ON to OFF | 3 seconds or more |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Engine speed signal | No signal |
| CKP sensor voltage | Less than 0.3 V |
| CKP sensor voltage | More than 4.7 V |
| CKP sensor |
|
| CKP sensor voltage | 0.3 to 4.7 V |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING TECHSTREAM (ENGINE SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.
Start the engine.
Read the values displayed on the Techstream while the engine is running.
|
| ||||
| OK | ||
| ||
| 2.INSPECT CRANKSHAFT POSITION SENSOR (SENSOR POWER SOURCE) |
![]() |
Disconnect the D1 crankshaft position sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D1-3 - Body ground | Ignition switch ON | 4.5 to 5.0 V |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
![]() |
Disconnect the D1 crankshaft position sensor connector.
Disconnect the D56 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D1-1 - D56-110 (NE+) | Always | Below 1 Ω |
| D1-2 - D56-111 (NE-) | Always | Below 1 Ω |
| D1-1 or D56-110 (NE+) - Body ground | Always | 10 kΩ or higher |
| D1-2 or D56-111 (NE-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR) |
![]() |
Check the crankshaft position sensor installation.
|
| ||||
| OK | |
| 5.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE) |
Check the teeth of the sensor plate.
|
| ||||
| OK | |
| 6.REPLACE CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335, P0337, P0338 AND/OR P0339) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Start the engine.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0335, P0337, P0338 and/or P0339 | B |
|
| ||||
| A | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
![]() |
Disconnect the D1 crankshaft position sensor connector.
Disconnect the D56 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D1-3 - D56-66 (VCV2) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||