Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR

REAR AIRBAG SENSOR > INSTALLATION

for Preparation Click here




1. INSTALL REAR AIRBAG SENSOR RH
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B193065
  1. Engage the guide and Install the rear airbag sensor.

  1. Install the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    CAUTION:
    1. If the rear airbag sensor LH has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the rear airbag sensor LH, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

  1. Check that there is no looseness in the installation parts of the rear airbag sensor.

  1. Connect the connector to the rear airbag sensor.



2. INSTALL REAR AIRBAG SENSOR LH

HINT:
Use the same procedure as for the RH side.



3. INSTALL REAR SIDE NO. 3 AIR DUCT


    E188149
  1. Install the air duct with the 2 clips.



4. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Standard)
  1. Connect the connector.

  1. Engage the 11 clips to install the quarter trim panel assembly.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B219907



    B190147
  1. Engage the 2 claws to install the cover.



    B190146
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190158
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190145
  1. Engage the 3 claws to install the outer lap belt anchor cover.



5. INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for Standard)
  1. Connect the connector.

  1. Engage the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B222458



    B193068
  1. Engage the 2 claws to install the cover.



    B191816
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Engage the 3 claws to install the outer lap belt anchor cover.



6. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat)
  1. Connect the 3 connectors.

  1. Engage the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B222459



    B190147
  1. Engage the 2 claws to install the cover.



    B190146
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190158
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190145
  1. Engage the 3 claws to install the outer lap belt anchor cover.



7. INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for Power Seat)
  1. Connect the 5 connectors.

  1. Engage the 12 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Engage the 2 clamps to install the wire harness.



  1. Install the 2 clips.


    B222460



    B193068
  1. Engage the 2 claws to install the cover.



    B191816
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Engage the 3 claws to install the outer lap belt anchor cover.



8. INSTALL REAR FLOOR MAT SUPPORT PLATE


B190142
  1. Engage the 5 clips to the 4 claws, and install the rear floor mat support plate.



9. INSTALL ROPE HOOK ASSEMBLY


B190141
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B190139
  1. Engage the 2 claws to install the cover.



10. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


B190154E01
  1. Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.
    Paint Mark 
    Area
    Color
    RH side
    Pink
    LH side
    Purple



11. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for both sides.



12. INSTALL REAR DOOR SCUFF PLATE RH


B186666
  1. Engage the 2 claws and 5 clips to install the rear door scuff plate.

  1. Install the 2 bolts.



    B186665
  1. Engage the 6 claws, 5 clips and 2 guides to install the rear door scuff plate.

  1. Install the screw.



13. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



14. INSTALL REAR FLOOR STEP NO. 1 COVER


B191404
  1. Engage the 2 claws to install the rear floor step No. 1 cover.



15. INSTALL REAR FLOOR STEP NO. 2 COVER


B193890
  1. Engage the 2 claws to install the rear floor step No. 2 cover.



16. INSTALL REAR SEAT CUSHION HINGE LOWER COVER RH


B191794
  1. Engage the 2 clips and 5 claws to install the rear cushion hinge lower cover RH.



17. INSTALL REAR SEAT CUSHION HINGE LOWER COVER LH

HINT:
Use the same procedure for both sides.



18. INSTALL REAR NO. 2 SEAT ASSEMBLY RH
  1. for Manual seat:
    Install the rear No. 2 seat assembly RH

  1. for Power Seat:
    Install the rear No. 2 seat assembly RH



19. INSTALL REAR NO. 2 SEAT ASSEMBLY LH
  1. for Manual seat:
    Install the rear No. 2 seat assembly LH

  1. for Power Seat:
    Install the rear No. 2 seat assembly LH



20. INSTALL DECK BOARD BRACKET


B190119
  1. Install the deck board bracket with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



21. INSTALL DECK BOARD REINFORCEMENT SUB-ASSEMBLY


B190120
  1. Install the deck board reinforcement with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



22. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY


B190117
  1. Engage the 5 clips to install the No. 1 deck board.



23. INSTALL ROPE HOOK ASSEMBLY


B191405
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    HINT:
    Use the same procedure for both sides.



24. INSTALL LUGGAGE COMPARTMENT TRIM BOX


B190116
  1. Install the luggage compartment trim box with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B194633
  1. Install the 4 caps.



25. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


B194608
  1. Engage the 4 guides to install the No. 2 deck board.



26. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



27. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).