Home › Engine / Hybrid System · 1UR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0443    Evaporative Emission Control System Purge Control Valve Circuit

for Preparation Click here


DESCRIPTION

HINT:
DTC P0443 is applicable to Mexico models only.

To reduce hydrocarbon emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.
The ECM changes the duty signals to the purge VSV (Vacuum Switching Valve for Purge Control) so that the intake amount of hydrocarbon emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No.
DTC Detection Condition
Trouble Area
P0443
Terminal voltage of ECM output circuit does not correspond with drive signals from ECM to purge VSV
(1 trip detection logic)
  1. Open or short in purge VSV circuit
  2. Purge VSV
  3. ECM

WIRING DIAGRAM


A196661E06


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE VSV FOR EVAP CONTROL)


    A214696E03
  1. Connect a Techstream to the DLC3.

  1. Disconnect the vacuum hose (charcoal canister side) from the purge VSV.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EVAP Control.

  1. When the purge VSV is operated using the Techstream, check whether the port of the purge VSV applies suction to your finger.

    OK:
    Tester Operation
    Specified Condition
    VSV ON
    Purge VSV port applies suction to finger
    VSV OFF
    Purge VSV port applies no suction to finger

    Text in Illustration 
    *1
    Purge VSV
    *2
    Hose (to Canister)



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT PURGE VSV (RESISTANCE)
  1. Inspect the purge VSV (Click here).



NG
REPLACE PURGE VSV (Click here)
OK


3.INSPECT PURGE VSV (POWER SOURCE)


    A161605E10
  1. Disconnect the purge VSV connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D16-1 - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Component without harness connected
(Purge VSV)


NG
Go to step 5
OK


4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
  1. Disconnect the purge VSV connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D16-2 - D56-63 (PRG)
    Always
    Below 1 Ω
    D16-2 or D56-63 (PRG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - INTEGRATION RELAY)
  1. Disconnect the purge VSV connector.

  1. Remove the integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D16-1 - 1B-4
    Always
    Below 1 Ω
    D16-1 or 1B-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR OR REPLACE FUSE
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)