Home › Drivetrain · A760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0705    Transmission Range Sensor Circuit Malfunction (PRNDL Input)

for Preparation Click here


DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.

DTC Code
DTC Detection Condition
Trouble Area
P0705
One of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2-trip detection logic):
  1. P input signal
  2. N input signal
  3. NSW input signal
  4. R input signal
  5. D input signal
(B) Any of the following signals is ON for 2.0 seconds or more with the shift lever in S (2-trip detection logic):
  1. P input signal
  2. N input signal
  3. NSW input signal
  4. R input signal
(C) All signals are OFF simultaneously for P, R, N and D positions (2-trip detection logic).
  1. Open or short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. Transmission control switch (Transmission floor shift assembly)
  4. ECM

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D or S).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.

MONITOR STRATEGY


Related DTCs
P0705: Park/neutral position switch/Verify switch input
Required sensors/Components
Park/neutral position switch
Frequency of operation
Continuous
Duration
Condition (A) and (B)
2 seconds
Condition (C)
60 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
None
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS

  1. One of the following conditions is met: Condition (A), (B) or (C)
  2. Condition (A)
    1. When 2 or more of the following signals are input at the same time

      P switch
      ON
      N switch
      ON
      NSW switch
      ON
      R switch
      ON
      D switch
      ON
    Condition (B)
    1. When the shift lever is in S, one of the following conditions is met

      P switch
      ON
      N switch
      ON
      NSW switch
      ON
      R switch
      ON
    Condition (C)
    1. All of the following conditions are met

      P switch
      OFF
      N switch
      OFF
      NSW switch
      OFF
      R switch
      OFF
      D switch
      OFF

COMPONENT OPERATING RANGE


Park/neutral position switch
The park/neutral position switch sends only one signal to the ECM

WIRING DIAGRAM


C162206E09


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).


DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the Techstream, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    1. Shift lever in P or N: ON
    2. Shift lever not in P or N: OFF
    When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (P Range)
    PNP switch status/
    ON or OFF
    1. Shift lever in P: ON
    2. Shift lever not in P: OFF
    When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (R Range)
    PNP switch status/
    ON or OFF
    1. Shift lever in R: ON
    2. Shift lever not in R: OFF
    When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (N Range)
    PNP switch status/
    ON or OFF
    1. Shift lever in N: ON
    2. Shift lever not in N: OFF
    When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Sports Shift Up SW
    Sport shift up switch status/
    ON or OFF
    1. ON: Shift lever held in "+" (up-shift)
    2. OFF: Shift lever not held in "+" (up-shift)
    -
    Sports Shift Down SW
    Sport shift down switch status/
    ON or OFF
    1. ON: Shift lever held in "-" (down-shift)
    2. OFF: Shift lever not held in "-" (down-shift)
    -
    Sports Mode Selection SW
    Sport mode select switch status/
    ON or OFF
    1. ON: Shift lever in S, "+" or "-"
    2. OFF: Shift lever not in S, "+" or "-"
    -
    Shift SW Status (D Range)
    PNP switch status/
    ON or OFF
    1. Shift lever in D, S, "+" or "-": ON
    2. Shift lever not in D, S, "+" or "-": OFF
    When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

1.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C208647E03
  1. Disconnect the D21 park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1. 2 (RB) - 6 (PL)
    2. 4 (B) - 5 (L)
    Shift lever in P
    Below 1 Ω
    2 (RB) - 1 (RL)
    Shift lever in R
    Below 1 Ω
    1. 2 (RB) - 9 (NL)
    2. 4 (B) - 5 (L)
    Shift lever in N
    Below 1 Ω
    2 (RB) - 7 (DL)
    Shift lever in D, S, "+" or "-"
    Below 1 Ω
    1. 2 (RB) - 6 (PL)
    2. 4 (B) - 5 (L)
    Shift lever not in P
    10 kΩ or higher
    2 (RB) - 1 (RL)
    Shift lever not in R
    10 kΩ or higher
    1. 2 (RB) - 9 (NL)
    2. 4 (B) - 5 (L)
    Shift lever not in N
    10 kΩ or higher
    2 (RB) - 7 (DL)
    Shift lever not in D, S, "+" or "-"
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Park/Neutral Position Switch)



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


2.INSPECT TRANSMISSION CONTROL SWITCH


    C203344E10
  1. Disconnect the H31 transmission control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (IG) - 7 (S)
    Shift lever in S, "+" or "-"
    Below 1 Ω
    3 (IG) - 7 (S)
    Shift lever not in S, "+" or "-"
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Control Switch)



NG
REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY) (Click here)
OK


3.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)


    C208648E03
  1. Disconnect the D21 park/neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D21-2 (RB) - Body ground
    Ignition switch ON
    11 to 14 V
    D21-2 (RB) - Body ground
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - IGNITION SWITCH)
OK


4.CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)


    C203343E11
  1. Disconnect the H31 transmission control switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H31-3 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    H31-3 (IG) - Body ground
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Transmission Control Switch)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - IGNITION SWITCH)
OK


5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)


    C197707E65
  1. Disconnect the D56 ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1. D56-2 (P) - Body ground
    2. D56-120 (NSW) - Body ground
    1. Ignition switch ON
    2. Shift lever in P
    11 to 14 V
    D56-26 (R) - Body ground
    1. Ignition switch ON
    2. Shift lever in R
    11 to 14 V*
    1. D56-25 (N) - Body ground
    2. D56-120 (NSW) - Body ground
    1. Ignition switch ON
    2. Shift lever in N
    11 to 14 V
    D56-27 (D) - Body ground
    1. Ignition switch ON
    2. Shift lever in D
    11 to 14 V
    1. D56-2 (P) - Body ground
    2. D56-120 (NSW) - Body ground
    1. Ignition switch ON
    2. Shift lever not in P
    Below 1 V
    D56-26 (R) - Body ground
    1. Ignition switch ON
    2. Shift lever not in R
    Below 1 V
    1. D56-25 (N) - Body ground
    2. D56-120 (NSW) - Body ground
    1. Ignition switch ON
    2. Shift lever not in N
    Below 1 V
    D56-27 (D) - Body ground
    1. Ignition switch ON
    2. Shift lever not in D
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)

    HINT:
    *: The voltage will drop slightly due to the illumination of the back-up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)


    C197708E24
  1. Disconnect the A27 ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A27-25 (S) - Body ground
    Shift lever in S, "+" or "-"
    11 to 14 V
    A27-25 (S) - Body ground
    Shift lever not in S, "+" or "-"
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)