Home › Drivetrain · A760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0712    Transmission Fluid Temperature Sensor "A" Circuit Low Input

DTC    P0713    Transmission Fluid Temperature Sensor "A" Circuit High Input

for Preparation Click here


DESCRIPTION

Refer to DTC P0711 .

DTC Code
DTC Detection Condition
Trouble Area
P0712
ATF temperature sensor resistance is less than 79 Ω for 0.5 sec. or more (1-trip detection logic).
  1. Short in ATF temperature sensor circuit
  2. ATF temperature sensor
  3. ECM
P0713
ATF temperature sensor resistance is more than 156 kΩ for 0.5 sec. or more and either of the following conditions is met (1-trip detection logic):
(A) 338 sec. or more have elapsed after the engine start when engine coolant temperature or intake air temperature is -29.375°C (-20.875°F) or less.
(B) 10 sec. or more have elapsed after the engine start when engine coolant temperature and intake air temperature are more than -29.375°C (-20.875°F).
  1. Open in ATF temperature sensor circuit
  2. ATF temperature sensor
  3. ECM

MONITOR DESCRIPTION

The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects an open or short in the ATF temperature sensor circuit. If the resistance value of the ATF temperature sensor is less than 79 Ω*1 or more than 156 kΩ*2, the ECM interprets this as a fault in the ATF temperature sensor or wiring. The ECM will illuminate the MIL and store the DTC.

HINT:
  1. *1: 150°C (302°F) or more is indicated regardless of the actual ATF temperature.
  2. *2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.
  3. The ATF temperature can be checked on the Techstream display.


MONITOR STRATEGY


Related DTCs
P0712: ATF temperature sensor/Range check (Low resistance)
P0713: ATF temperature sensor/Range check (High resistance)
Required sensors/Components
ATF temperature sensor
Frequency of operation
Continuous
Duration
0.5 seconds
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS

P0712: Range check (Low resistance)

  1. The monitor will run whenever the following DTCs are not present
    None
    Battery voltage
    8 V or more
    Ignition switch
    ON
    Starter
    OFF
P0713: Range check (High resistance)
  1. Either condition is met: Condition (A) or (B)
  2. Condition (A)

    1. The monitor will run whenever the following DTCs are not present
      P0115, P0117, P0118 (ECT (Engine Coolant Temperature) sensor circuit)
      P00AC, P00AD, P0110, P0112, P0113 (IAT (Intake Air Temperature) sensor circuit)
      Engine coolant temperature or intake air temperature at engine start
      -29.375°C (-20.875°F) or less
      Time after engine start
      338 seconds or more
      Battery voltage
      8 V or more
      Ignition switch
      ON
      Starter
      OFF
    Condition (B)

    1. The monitor will run whenever the following DTCs are not present
      P0115, P0117, P0118 (ECT (Engine Coolant Temperature) sensor circuit)
      P00AC, P00AD, P0110, P0112, P0113 (IAT (Intake Air Temperature) sensor circuit)
      Engine coolant temperature and intake air temperature at engine start
      More than -29.375°C (-20.875°F)
      Time after engine start
      10 seconds or more
      Battery voltage
      8 V or more
      Ignition switch
      ON
      Starter
      OFF

TYPICAL MALFUNCTION THRESHOLDS


P0712: Range check (Low resistance) 
ATF temperature sensor resistance
Less than 79 Ω

P0713: Range check (High resistance) 
ATF temperature sensor resistance
More than 156 kΩ

COMPONENT OPERATING RANGE


ATF temperature sensor resistance
79 Ω to 156 kΩ

WIRING DIAGRAM


C155188E17


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).


DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the Techstream, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. Equal to ambient temperature when engine cold
    If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted.

    HINT:
    When DTC P0712 is output and the Techstream output is 150°C (302°F) or more, there is a short circuit.
    When DTC P0713 is output and the Techstream output is -40°C (-40°F), there is an open circuit.
    Check the temperature displayed on the tester in order to check if a malfunction exists.


    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    150°C (302°F) or more
    Short circuit
    If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately stored (in 0.5 seconds). When P0713 is stored, P0711 cannot be stored.
    It is not necessary to inspect the circuit when P0711 is stored.

1.INSPECT TRANSMISSION WIRE (NO. 1 ATF TEMPERATURE SENSOR)


    C210154E13
  1. Disconnect the D73 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (OT-) - 13 (OT+)
    Always
    79 Ω to 156 kΩ
    2 (OT-) - Body ground
    Always
    10 kΩ or higher
    13 (OT+) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

    Standard Resistance:
    ATF Temperature
    Specified Condition
    10°C (50°F)
    5 to 8 kΩ
    25°C (77°F)
    2.5 to 4.5 kΩ
    110°C (230°F)
    0.22 to 0.28 kΩ

Text in Illustration 
*a
Component without harness connected
(Transmission Wire)


NG
REPAIR OR REPLACE TRANSMISSION WIRE (NO. 1 ATF TEMPERATURE SENSOR) (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    C197707E66
  1. Disconnect the D56 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D56-122 (THO1) - D56-98 (E2)
    Always
    79 Ω to 156 kΩ
    D56-122 (THO1) - Body ground
    Always
    10 kΩ or higher
    D56-98 (E2) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)