Home › Engine / Hybrid System · 3UR-FBE › ENGINE CONTROL › SFI SYSTEM

DTC    P0031    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)

DTC    P0032    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)

DTC    P0051    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)

DTC    P0052    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)

DTC    P101D    A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON

DTC    P103D    A/F Sensor Heater Circuit Performance Bank 2 Sensor 1 Stuck ON

for Preparation Click here


DESCRIPTION

Refer to DTC P2195 .

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
  3. When one of these DTCs is set, the ECM enters fail-safe mode. The ECM turns off the A/F sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

  4. The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The A/F sensor heater circuit uses a relay on the +B side of the circuit.


    A164715E06


DTC No.
DTC Detection Condition
Trouble Area
P0031
P0051
Air-Fuel Ratio (A/F) sensor heater current less than 0.8 A
(1 trip detection logic)
  1. Open in A/F sensor heater circuit
  2. A/F sensor heater (for Sensor 1)
  3. Integration relay
  4. ECM
P0032
P0052
Air-Fuel Ratio (A/F) sensor heater current failure
(1 trip detection logic)
  1. Short in A/F sensor heater circuit
  2. A/F sensor heater (for Sensor 1)
  3. Integration relay
  4. ECM
P101D
P103D
The heater current is higher than the specified value while the heater is not operating.
(1 trip detection logic)
ECM

HINT:
  1. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  2. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.


MONITOR DESCRIPTION

The ECM uses information from the Air-Fuel Ratio (A/F) sensor to regulate the air-fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the Three-Way Catalytic Converter (TWC) to purify the exhaust gases.
The A/F sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum coated zirconia and includes an integrated heating element.
The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.
The A/F sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the A/F sensor becomes inaccurate. As a result, the ECM is unable to regulate the air-fuel ratio properly.
When the current in the A/F sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0031: A/F sensor heater (for Bank 1) open/short (Low electrical current)
P0032: A/F sensor heater (for Bank 1) open/short (High electrical current)
P0051: A/F sensor heater (for Bank 2) open/short (Low electrical current)
P0052: A/F sensor heater (for Bank 2) open/short (High electrical current)
P101D: A/F sensor heater (for Bank 1) performance
P103D: A/F sensor heater (for Bank 2) performance
Required Sensors/Components (Main)
A/F sensor heater
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
11 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P0031 and P0051 
Monitor runs whenever following DTCs not stored
None
Battery voltage
10.5 V or more
Time after heater ON
5 seconds or more
Active heater OFF control
Not operating
Active heater ON control
Not operating
Heater output duty
30% or more
A/F sensor heater performance failure (P101D, P103D)
Not detected

P0032 and P0052 
Monitor runs whenever following DTCs not stored
None
Battery voltage
10.5 V or more
Time after heater ON
5 seconds or more
Active heater OFF control
Not operating
Active heater ON control
Not operating
Heater output duty
More than 0%

P101D and P103D 
Monitor runs whenever following DTCs not stored
None
Battery voltage
10.5 V or more
Time after heater ON
5 seconds or more
A/F sensor heater duty-cycle ratio
10 to 60%
A/F sensor heater ON current
0.8 A or higher
Active heater OFF control
Not operating
Active heater ON control
Not operating
Air fuel ratio sensor heater range check low current failure (P0031, P0051)
Not detected

TYPICAL MALFUNCTION THRESHOLDS


P0031 and P0051 
Air fuel ratio sensor heater ON current
Less than 0.8 A

P0032 and P0052 
Air fuel ratio sensor heater output
ON
Hybrid IC high current limiter port
Fail

P101D and P103D 
Air fuel ratio sensor heater OFF current
Higher than 11 A
Active heater OFF control for stuck ON malfunction
Operating
Hybrid IC high current limiter port
Fail

COMPONENT OPERATING RANGE


A/F sensor heater current
0.9 to 9.9 A

CONFIRMATION DRIVING PATTERN


A198819E21

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream ON.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and idle it for 5 minutes or more [B].
  7. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
  8. Idle the engine for 5 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read the pending DTC.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0031, P0032, P0051, P0052, P101D or P103D.
  13. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
  14. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.
  15. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
A150241E06
  1. Disconnect the D19 or D20 A/F sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.6 to 3.2 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.6 to 3.2 Ω
    1 (HA2A) - 4 (A2A-)
    Always
    10 kΩ or higher



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


2.CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR)
A150242E21
  1. Disconnect the D19 or D20 A/F sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D19-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    D20-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 5
A


3.INSPECT INTEGRATION RELAY (A/F)
A148742E04
  1. Remove the integration relay from the engine room relay block.

  1. Inspect the A/F fuse.

    1. Remove the A/F fuse from the integration relay.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A/F fuse
      Always
      Below 1 Ω

    3. Reinstall the A/F fuse.

  1. Inspect the integration relay (A/F).

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1A-4
      When no battery voltage applied to terminals 1A-2 and 1A-3
      10 kΩ or higher
      When battery voltage applied to terminals 1A-2 and 1A-3
      Below 1 Ω



NG
REPLACE INTEGRATION RELAY (A/F)
OK


4.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - A/F SENSOR AND BODY GROUND)
A164716E05
  1. Disconnect the D19 or D20 A/F sensor connector.

  1. Remove the integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D19-2 (+B) - 1A-4
    Always
    Below 1 Ω
    D20-2 (+B) - 1A-4
    Always
    Below 1 Ω
    1A-2 - 1B-5
    Always
    Below 1 Ω
    1A-3 - Body ground
    Always
    Below 1 Ω
    D19-2 (+B) or 1A-4 - Body ground
    Always
    10 kΩ or higher
    D20-2 (+B) or 1A-4 - Body ground
    Always
    10 kΩ or higher
    1A-2 or 1B-5 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)  

5.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
A160209E10
  1. Disconnect the D19 or D20 A/F sensor connector.

  1. Disconnect the D56 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D19-1 (HA1A) - D56-22 (HA1A)
    Always
    Below 1 Ω
    D20-1 (HA2A) - D56-20 (HA2A)
    Always
    Below 1 Ω
    D19-1 (HA1A) or D56-22 (HA1A) - Body ground
    Always
    10 kΩ or higher
    D20-1 (HA2A) or D56-20 (HA2A) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    No DTC is output
    A
    P0031, P0032, P0051, P0052, P101D or P103D is output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)