Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C0200/31    Right Front Wheel Speed Sensor Signal

DTC    C0205/32    Left Front Wheel Speed Sensor Signal

DTC    C1271/71    Low Output Signal of Front Speed Sensor RH (Test Mode DTC)

DTC    C1272/72    Low Output Signal of Front Speed Sensor LH (Test Mode DTC)

DTC    C1275/75    Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)

DTC    C1276/76    Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)

DTC    C1330/35    Open Circuit in Right Front Wheel Speed Sensor Circuit

DTC    C1331/36    Open Circuit in Left Front Wheel Speed Sensor Circuit

for Preparation Click here


DESCRIPTION

The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU.
Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change as the rotors turn.
The speed sensors detect those magnetic changes and send pulse signals to the skid control ECU. The ECU monitors the wheel speeds through these pulse signals to control the ABS control system.

C152717E03

HINT:
When testing voltage, perform the test while the connector between the sensor and ECU is connected. Do not disconnect the connector between the sensor and ECU.


DTC Code
DTC Detection Condition
Trouble Area
C0200/31
C0205/32
When any of following conditions detected:
  1. When vehicle speed 15 km/h (9 mph), wheel speed 6 km/h (4 mph) or less.
  2. At vehicle speed of 45 km/h (28 mph) or more, open in sensor harness occurs intermittently for 0.2 seconds or more.
  3. When vehicle speed between 10 km/h (6 mph) and 15 km/h (9 mph) for 3 minutes, one wheel speed 0 km/h (0 mph).
  4. Pressure reduction mode of ABS system lasts for 28 seconds or more.
  5. When vehicle driven at speed of 20 km/h (12 mph) or more, difference between wheel speeds indicated by two sensors twice or more for 30 seconds or more.
  6. Foreign matter adheres to sensor rotor.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1271/71
C1272/72
Detected only during test mode.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1275/75
C1276/76
Detected only during test mode.
  1. Front speed sensor (open)
  2. Front speed sensor circuit (open)
C1330/35
C1331/36
Open in front speed sensor circuit continues for 0.15 seconds or more.
  1. Front speed sensor (open)
  2. Front speed sensor circuit (open)

HINT:
  1. DTCs C0200/31 and C1330/35 are for the front speed sensor RH.
  2. DTCs C0205/32 and C1331/36 are for the front speed sensor LH.


WIRING DIAGRAM


C241007E11


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the VSC actuator assembly, perform zero point calibration (Click here).
  2. Check the speed sensor signal in test mode after cleaning or replacement (Click here).

1.READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List mode on the Techstream.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Front wheel speed sensor RH reading /
    min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer
    FL Wheel Speed
    Front wheel speed sensor LH reading /
    min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer

  1. Check that the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer are almost the same when driving the vehicle.

    OK:
    The speed value output from the speed sensor displayed on the Techstream is the same as the actual vehicle speed.

    HINT:
    There is a tolerance of +/-10% in the speedometer indication.



NG
Go to step 4
OK


2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
  1. Perform a TEST MODE inspection and check for DTCs (Click here).

    OK:
    No DTC output.



NG
Go to step 4
OK


3.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
Go to step 10
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

4.CHECK FRONT SPEED SENSOR INSTALLATION
I044006E20
  1. Check that the speed sensor installation bolt is tightened properly (Click here).

    OK:
    The installation bolt is tightened properly.



NG
TIGHTEN BOLT PROPERLY (Click here)
OK


5.CHECK FRONT SPEED SENSOR
  1. Visually check the speed sensor for deformation and damage.

    OK:
    No deformation or damage.
    There is no gap between the sensor and front steering knuckle.



NG
REPLACE FRONT SPEED SENSOR (Click here)
OK


6.CHECK SPEED SENSOR TIP
  1. Remove the speed sensor (Click here).

  1. Check the sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.



NG
CLEAN OR REPLACE SPEED SENSOR (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)


    C240469E03
  1. Confirm that the skid control ECU connector and speed sensor connector are properly connected.

  1. Disconnect the A19 ECU connector.

  1. Disconnect the z3 and z4 sensor connectors.

  1. Inspect both the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    A19-34 (FR+) - z3-2
    Always
    Below 1 Ω
    A19-33 (FR-) - z3-1
    A19-34 (FR+) - Body ground
    Always
    10 kΩ or higher
    A19-33 (FR-) - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    A19-45 (FL+) - z4-2
    Always
    Below 1 Ω
    A19-46 (FL-) - z4-1
    A19-45 (FL+) - Body ground
    Always
    10 kΩ or higher
    A19-46 (FL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT FRONT SPEED SENSOR (INPUT VOLTAGE)


    C156480E53
  1. Reconnect the A19 ECU connector.

  1. Disconnect the z3 and z4 sensor connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    z3-2 - Body ground
    Ignition switch ON
    7.5 to 20 V
    z4-2 - Body ground



NG
REPLACE VSC ACTUATOR ASSEMBLY (Click here)
OK


9.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)
A


10.REPLACE FRONT SPEED SENSOR
  1. Replace the front speed sensor (Click here).


NEXT


11.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE VSC ACTUATOR ASSEMBLY (Click here)