Home › Engine / Hybrid System · 1UR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0013    Camshaft Position "B" Actuator Circuit / Open (Bank 1)

DTC    P0023    Camshaft Position "B" Actuator Circuit / Open (Bank 2)

for Preparation Click here


DESCRIPTION

  1. These DTCs are designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.
  2. The VVT (variable valve timing) system adjusts the intake and exhaust valve timing to improve driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The OCV is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 volts to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A192077E02


DTC No.
DTC Detection Condition
Trouble Area
P0013
Open or short in OCV for exhaust camshaft (for Bank 1) circuit
(1 trip detection logic)
  1. Open or short in OCV for exhaust camshaft (for Bank 1) circuit
  2. OCV for exhaust camshaft (for Bank 1)
  3. ECM
P0023
Open or short in OCV for exhaust camshaft (for Bank 2) circuit
(1 trip detection logic)
  1. Open or short in OCV for exhaust camshaft (for Bank 2) circuit
  2. OCV for exhaust camshaft (for Bank 2)
  3. ECM

MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

MONITOR STRATEGY


Related DTCs
P0013: Exhaust camshaft OCV (for Bank 1)
P0023: Exhaust camshaft OCV (for Bank 2)
Required sensors/Components (Main)
Exhaust camshaft OCV
Required sensors/Components (Related)
-
Frequency of operation
Continuous
Duration
1 second
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
All of following conditions met
-
Starter
OFF
Ignition switch
ON
Time after ignition switch off to ON
0.5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


One of following conditions met
-
A. All of following conditions met
-
Battery voltage
11 to 13 V
Target duty ratio
Less than 70%
Output signal duty ratio
100%
B. All of following conditions met
-
Battery voltage
13 V or more
Target duty ratio
Less than 80%
Output signal duty ratio
100%
C. Both of following conditions met
-
Current cut status
Not cut
Output signal duty ratio
3% or less

COMPONENT OPERATING RANGE


OCV duty-cycle
3 to 100%

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Wait 5 seconds.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.
  8. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0013 or P0023.
  11. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A178641E03


INSPECTION PROCEDURE

HINT:
  1. If DTC P0013 is displayed, check the bank 1 VVT system for exhaust camshaft circuit.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  4. If DTC P0023 is displayed, check the bank 2 VVT system for exhaust camshaft circuit.
  5. Bank 2 refers to the bank that does not include the No. 1 cylinder.

1.CHECK FOR DTC (DTC P0013 OR P0023)
  1. Connect the Techstream to the DLC3.

  1. Clear DTCs after recording the freeze frame data and DTCs (Click here).

  1. Turn the ignition switch off.

  1. Allow the engine to idle and check for DTCs.

  1. Check that P0013 or P0023 is not output.

    OK:
    P0013 or P0023 is not output.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT CAMSHAFT OIL CONTROL VALVE
  1. Inspect the camshaft oil control valve (Click here).



NG
REPLACE CAMSHAFT OIL CONTROL VALVE ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (OCV - ECM)
  1. Disconnect the OCV connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D28-1 - D56-56 (OE1+)
    Always
    Below 1 Ω
    D28-2 - D56-55 (OE1-)
    Always
    Below 1 Ω
    D29-1 - D56-50 (OE2+)
    Always
    Below 1 Ω
    D29-2 - D56-49 (OE2-)
    Always
    Below 1 Ω
    D28-1 or D56-56 (OE1+) - Body ground
    Always
    10 kΩ or higher
    D28-2 or D56-55 (OE1-) - Body ground
    Always
    10 kΩ or higher
    D29-1 or D56-50 (OE2+) - Body ground
    Always
    10 kΩ or higher
    D29-2 or D56-49 (OE2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)