DTC P0412 Secondary Air Injection System Switching Valve "A" Circuit |
DTC P0415 Secondary Air Injection System Switching Valve "B" Circuit |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0412 P0415 |
|
|
| P0412 P0415 |
|
|
| Related DTCs | P0412: Secondary air injection system air switching valve circuit range check (Bank 1) P0415: Secondary air injection system air switching valve circuit range check (Bank 2) |
| Required Sensors/Components (Main) | Air injection control driver |
| Required Sensors/Components (Related) | Air switching valve |
| Frequency of Operation | Once per drive cycle |
| Duration | 3 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | - |
| Secondary air injection pump | Operating |
| Secondary air injection switching valve | Operating |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Monitor runs whenever following DTCs not stored | - |
| Secondary air injection pump | Not operating |
| Secondary air injection switching valve | Not operating |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Diagnostic signal duty ratio from air injection control driver | 31% or more, and 48% or less |
| Diagnostic signal duty ratio from air injection control driver | 70% or more, and 90% or less when secondary air injection system operating. 0% when secondary air injection system not operating. |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|


| 1.INSPECT AIR SWITCHING VALVE |
![]() |
Disconnect the D37 or D38 ASV connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D37-5 (+B) - D37-1 (GND) | 20°C (68°F)* | 4.5 to 5.5 Ω |
| D38-5 (+BL) - D38-1 (GNDL) | 20°C (68°F)* | 4.5 to 5.5 Ω |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - BODY GROUND) |
![]() |
Disconnect the D37 or D38 ASV connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D37-1 (GND) - Body ground | Always | Below 1 Ω |
| D38-1 (GNDL) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - AIR INJECTION CONTROL DRIVER) |
![]() |
Disconnect the D37 or D38 ASV connector.
Disconnect the D32 or D34 AID connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D37-5 (+B) - D32-6 (VV) | Always | Below 1 Ω |
| D38-5 (+BL) - D34-6 (VV2) | Always | Below 1 Ω |
| D37-5 (+B) or D32-6 (VV) - Body ground | Always | 1 kΩ or higher |
| D38-5 (+BL) or D34-6 (VV2) - Body ground | Always | 1 kΩ or higher |
|
| ||||
| OK | ||
| ||